Sony SPK-IP55 User Manual

Page of 2
E
A
Operating Instructions
Mode d’emploi
Bedienunganleitung
Istruzioni per l’uso
Usable at the depth as low as 2 meters (6.5 feet) under water.
For using your video camera recorder with this pack, refer to the operating
instructions of the recorder.
This Sports Pack SPK-IP55 is exclusively for use with the Sony digital video
camera recorder DCR-IP55/DCR-IP55E/DCR-IP45/DCR-IP45E.
The splash-proof sports pack SPK-IP55 is water- and moisture- resistant,
making it possible to use the Sony digital video camera recorder.
Notice
•Before you start recording, make sure that the video camera recorder is
working correctly and there is no water leakage.
•Sony does not accept liability for damage to the video camera recorder,
battery, etc., when using the sports pack or for the cost of recording if
water leakage occurs as a result of incorrect use.
Precautions
•Do not subject the front glass to strong shock, as it may crack.
•Avoid opening the sports pack in the sea or at the beach. Preparation such
as installing and changing a cassette tape and the “Memory Stick” should
be done in a place with low humidity and no salty air.
•Do not throw the sports pack into the water.
•Avoid using the sports pack in places with storong waves.
•Avoid using the sports pack under the following situations:
– in a very hot or humid place.
– in water hotter than 40˚C (104˚F).
– at temperatures lower than 0˚C.
In these situations moisture condensation or water leakage may occur and
damage the equipment.
•Use the sports pack for no longer than one hour at a time in temperatures
above 35˚C (95˚F).
•Do not leave the sports pack under direct sunlight for a long period of
time. If you cannot avoid leaving the sports pack under direct sunlight, be
sure to cover the pack with a towel or other protection.
•If sun oil is on the sports pack, be sure to wash it off thoroughly using
lukewarm water. If the sports pack is left with sun oil on its body, the
surface of the sports pack may become discolored or damaged. (such as
cracks on the surface)
Maintenance and Precautions
Water Leakage
If water happens to leak in, stop exposing the sports pack to water
immediately.
If the video camera recorder gets wet, take it to the nearest Sony service
facility immediately.
Repair costs must be borne by the customer.
Notes on the Waterproof Gasket
•Check that there are no scratches or cracks on the waterproof gasket as
they may allow water to leak in. If there are scratches or cracks, replace
the damaged waterproof gasket with a new one.
Do not remove the waterproof gasket with a metal tool or a tool with a
sharp point.
•After checking that there are no cracks or dust on the waterproof gasket,
coat it slightly with the supplied grease using your finger. This will
prevent wearing.
While applying the grease, recheck for cracks or dust.
Never use cloth or paper for greasing as the fibers may cling.
Do not use any type of grease other than that supplied, as it may damage
the waterproof gasket.
•Put the waterproof gasket in the grooves evenly, with the tapering side
up. Never twist it. (See illustration A)
•The useful life of the waterproof gasket depends upon the maintenance
and the frequency of use, but we recommend changing it once a year. To
replace the waterproof gasket, please consult the nearest Sony dealer. Be
sure to check the water leakage after replacing the waterproof gasket.
Checking for the water leakage after replacing the
waterproof gasket
Check for the water leakage before installing the video camera recorder.
Close the sports pack without installing the video camera recorder, and
keep the sports pack submerged under water at a depth of about 15 cm (6
inches) for about 3 minutes and then check for water leakage.
After Recording
After recording in a location subject to sea breezes, wash the sports pack
with fresh water with the buckles fastened thoroughly, then wipe with a
soft dry cloth. It is recommended that you submerge the sports pack in
fresh water for about 30 minutes. If it is left with salt on it, metal portions
may be damaged or rust may form and cause water leakage.
•If you get suntan lotion or other greasy substances on your sports pack,
wash it off with tepid water.
•Clean the inside of the pack with a soft dry cloth. Do not wash the inside
of the pack.
•Do not use any type of solvent such as alcohol, benzine or thinner for
cleaning, as this might damage the finish.
Anti-fogging lens solution
Coat the surface of the glass with the supplied anti-fogging lens solution.
This is effective in preventing from fogging.
How to use the anti-fogging lens solution
Apply 1 or 2 drops of the liquid to the front glass and the glass of the eye
cup and wipe evenly to spread the liquid out by using the swabs, a soft
cloth or tissue paper.
When storing the sports pack
•Attach the spacer supplied with your sports pack to prevent wear of the
waterproof gasket. (See illustration B)
•Close the pack without fastening the buckles to prevent wear of the
waterproof gasket.
•Prevent dust from collecting on the waterproof gasket.
•Avoid storing the sports pack in a cold, very hot or humid place, or
together with naphthalene or camphor, as these conditions might damage
the unit.
Troubleshooting
Symptom
The sound is not
recorded.
There are drop
of water inside
of the sports
pack.
The recording
and playing
back function
does not work.
Specifications
Material
Plastic (PC, ABS), glass
Waterproof
Waterproof gasket, buckles
Built-in microphone
Stereo
Dimension
Approx. 125 
× 128 × 172 mm (w / h / d)
(5 
× 5 
1
/
8
 
× 6 
7
/
8
 inches)
Mass
Approx. 520 g (1 lb 2 oz) (only sports pack)
Supplied accessories
Shoulder strap (1)
Camera mounting shoe (1)
Reflex prevention ring (1)
Grease (1)
Spacer (1)
Anti-fogging lens solution (1)
Operating Instructions (1)
Design and specifications subject to change without notice.
Utilisable à une profondeur de 2 mètres (6,5 pieds) sous l’eau.
Pour l’emploi du caméscope avec ce caisson, reportez-vous au mode
d’emploi du caméscope.
Le caisson étanche SPK-IP55 doit être utilisé exclusivement avec les
caméscopes numériques Sony DCR-IP55/DCR-IP55E/DCR-IP45/DCR-
IP45E.
Le caisson SPK-IP55 est étanche aux projections d’eau et à l’humidité.
Attention
•Avant la prise de vues, assurez-vous que le caméscope fonctionne
correctement et qu’il n’y a pas d’infiltration d’eau.
•Sony décline toute responsabilité quant aux dommages que peuvent
subir, entre autres, le caméscope, la batterie, lorsqu’ils sont utilisés avec
le caisson, ou au coût d’un enregistrement perdu à la suite d’une
infiltration d’eau résultant d’un usage inadapté du caisson.
Précautions
•Ne pas cogner le verre avant. Il pourrait se fissurer.
•Evitez d’ouvrir le caisson en mer ou à la plage. La mise en place ou le
changement de cassette et du “Memory Stick” doivent être effectués à
l’abri de l’humidité et de l’air salin.
•Ne pas jeter le caisson dans l’eau.
•Evitez d’utiliser le caisson dans une mer agitée.
•Evitez d’utiliser le caisson dans les situations suivantes :
– un endroit très chaud ou très humide.
– eau à plus de 40˚C (104˚F).
– températures inférieures à 0˚C.
Dans ces situations de l’humidité risque de se condenser ou ou de l’eau
peut s’infiltrer et endommager l’appareil.
•N’utilisez pas le caisson plus d’une heure lorsque la température est
supérieure à 35˚C (95˚F).
•N’exposez pas le caisson au rayonnement direct du soleil pendant une
période prolongée. Si vous ne pouvez éviter de laisser le caisson en plein
soleil, recouvrez-le d’une serviette par exemple.
•De l’huile solaire tombée sur le caméscope peut décolorer ou
endommager le caisson marin (craquelures) s’il reste exposé au soleil.
Lavez soigneusement l’huile avec de l’eau tiède pour éviter ces
problèmes.
Entretien et précautions
Infiltration d’eau
Si de l’eau s’infiltre à l’intérieur du caisson, sortez immédiatement le
caisson de l’eau.
Si le caméscope est mouillé, présentez-le immédiatement au service après-
vente Sony le plus proche.
Les réparations sont à la charge du client.
Remarques sur le joint d’étanchéité
•Assurez-vous que le joint d’étanchéité n’est ni éraflé ni craquelé, sinon de
l’eau risque de s’infiltrer dans le caisson. Replacez le joint s’il est
endommagé.
N’enlevez pas le joint d’étanchéité à l’aide d’un objet métallique ou
pointu.
•Après avoir vérifié qu’il n’y a ni fissure ni poussière sur le joint
d’étanchéité, recouvrez-le avec le doigt d’une légère couche de la graisse
fournie, de façon à le protéger de l’usure.
Lorsque vous appliquez la graisse, revérifiez la présence éventuelle de
craquelures ou de poussière.
N’utilisez pas de chiffon ou de papier pour graisser le joint d’étanchéité
parce que des fibres risquent d’adhérer au joint.
N’utilisez aucun autre type de graisse que la graisse fournie, car vous
risqueriez sinon d’endommager le joint d’étanchéité.
•Insérez le joint d’étanchéité de manière égale dans les fentes avec le côté
en biseau orienté vers le haut. Ne le tordez pas. (Voir l’illustration A)
•La durée de vie du joint d’étanchéité dépend de l’entretien et de la
fréquence d’utilisation, mais il est conseillé de le remplacer une fois par
an. Pour le remplacement du joint d’étanchéité, veuillez vous adresser à
votre revendeur Sony. Après avoir remplacé le joint, assurez-vous de
l’étanchéité du caisson.
Vérification de l’étanchéité du caisson après le
remplacement du joint
Assurez-vous que le caisson est bien étanche avant d’installer le caméscope.
Refermez le caisson étanche sans installer le caméscope à l’intérieur et
laissez-le immergé dans l’eau à une profondeur d’environ 15 cm (6 pouces)
pendant 3 minutes environ et, et vérifiez si de l’eau ne s’est pas infiltrée.
Après la prise de vue
Après une prise de vue dans un endroit exposé aux embruns marins, rincez
le caisson étanche à l’eau douce en laissant les boucles fermées, puis
essuyez-le à l’aide d’un chiffon doux et sec. Il est conseillé de laisser le
caisson dans l’eau pendant 30 minutes environ. S’il reste du sel sur le
caisson, les pièces métalliques risquent d’être endommagées ou de rouiller,
ce qui peut entraîner une infiltration d’eau.
•Si de la crème de bronzage ou d’autres substances grasses tambent le
caisson, lavez-le à l’eau courante.
•Nettoyez l’intérieur du caisson avec un chiffon doux et sec. Ne rincez pas
l’intérieur du caisson étanche.
•Ne pas utiliser de solvant, comme l’alcool, la benzine ou le diluant, pour
le nettoyage car ces produits peuvent endommager la finition.
Solution antibuée
Appliquez sur la vitre un peu de solution antibuée pour objectif (fournie).
Cette solution est un moyen efficace pour éviter la formation de buée sur la
vitre.
Comment utiliser la solution antibuée
Appliquez 1 ou 2 gouttes de liquide sur la vitre frontale et sur le verre de
l’oculaire. Etalez uniformément le liquide à l’aide d’un coton-tige, d’un
chiffon doux ou d’un mouchoir en papier.
Rangement du caisson étanche
•Insérez l’entretoise fournie avec le caisson pour protéger le joint de
l’usure. (Voir l’illustration B)
•Refermez le caisson sans serrer les boucles de façon à éviter toute usure
du joint d’étanchéité.
•Evitez l’accumulation de poussière sur le joint d’étanchéité.
•Ne rangez pas le caisson étanche dans un endroit très froid, chaud ou
humide ou encore en présence de naphtaline ou de camphre, car le
caisson peut être endommagé.
En cas de problème
Symptôme
Le son n’est pas
enregistré.
Il y a des gouttes
d’eau à l’intérieur du
caisson.
La fonction de
lecture/
enregistrement est
inopérante.
Spécifications
Matériau
Plastique (PC, ABS), verre
Etanchéité
Joint d’étanchéité, boucles
Microphone intégré
Stéréo
Dimensions
Approx. 125 
× 128 × 172 mm (l / h / p)
(5 
× 5 
1
/
8
 
× 6 
7
/
8
 po)
Masse
Approx. 520 g (1 lb 2 oz) (caisson seul)
Accessoires fournis
Bandoulière (1)
Sabot de montage de caméscope (1)
Bague antireflet (1)
Graisse (1)
Entretoise (1)
Solution antibuée (1)
Mode d’emploi (1)
La conception et les spécifications sont sujettes à modifications sans préavis.
Préparation
Pour plus de détails, consultez le mode d’emploi fourni avec votre
caméscope.
D Préparation du caméscope
1 Retirez la lanière, le filtre ou le convertisseur du caméscope.
2 Installez la batterie.
3 Introduisez la cassette et le “Memory Stick”.
Déverrouillez le taquet de sécurité du “Memory Stick” et de la cassette pour
pouvoir enregistrer.
Assurez-vous que l’espace est suffisant sur le “Memory Stick” et la cassette pour
l’enregistrement.
4 Fixez la bague antireflet.
La bague antireflet empêche partiellement la bague de l’objectif de se refléter sur le
verre du caisson.
5 Pour les prises de vue avec l’écran LCD, retournez le panneau de
l’écran LCD et rabattez-le contre le caméscope avec l’écran LCD
orienté vers l’extérieur.
6 Réglez les fonctions telles que la mise au point et l’éclairage sur
AUTO.
E Installation du caméscope
Mettez le commutateur POWER du caméscope en position “OFF” (CHG) et
laissez le commutateur POWER du caisson sur “OFF”.
1 Fixez le sabot de montage du caméscope.
Utilisez les pièces métalliques de la bandoulière comme indiqué dans l’illustration.
2 Desserrez les boucles.
1
Faites glisser le bouton de déverrouillage dans le sens de la flèche et desserrez
les boucles.
2
Ouvrez la partie arrière du caisson.
Passez du liquide antibuée (fourni) pour objectif sur le verre avant.
3 Enlevez les matières étrangères.
Enlevez par exemple la poussière, les grains de sable ou les cheveux de la surface
du joint, de la rainure et de toutes les surfaces en contact. Insérez ensuite de
manière régulière le joint dans la rainure.
Si vous fermez le caisson sans nettoyer le joint, la surface du joint risque d’être
endommagée et de laisser l’eau s’infiltrer.
4 Installation du caméscope.
Alignez le sabot de montage du caméscope sur le guide de la partie avant du
caisson.
Introduisez le caméscope en poussant l’arrière du sabot de montage du caméscope
jusqu’à ce qu’il s’encliquette. Vérifiez si les boutons situés de part et d’autre du
sabot de montage du caméscope sont correctement serrées. Ne pas coincer les
cordons.
Remarque
Veillez à tenir le caméscope à l’horizontale lorsque vous l’installez.
L’insertion du caméscope à la verticale dans le caisson peut
endommager le sabot de montage et la partie avant du caisson.
5 Branchez les fiches sur chaque prise du caméscope. (Voir
l’illustration E-5)
1
Branchez la fiche de télécommande sur la prise 
 LANC.
2
Branchez ensuite la fiche de microphone sur la prise A/V.
6 Fermez la partie arrière du caisson.
Fixez ensuite la partie arrière et fermez les boucles de sorte qu’elles s’encliquettent.
Remarque
•Veillez à ne pas coincer les cordons lorsque vous fermez la partie
arrière.
•Lorsque le caméscope est dans le caisson, l’objectif peut être
légèrement décalé par rapport à la vitre du caisson. L'enregistrement
s’effectue toutefois sans problème.
F Préparation du caisson
1 Ajustez la sangle.
Saisissez le caisson étanche de façon à ce que vos doigts atteignent facilement le
commutateur POWER, la touche START/STOP et la touche ZOOM. Tirez sur la
sangle pour l’ajuster à la longueur adéquate.
2 Fixez la sangle.
La marque SONY doit être orientée vers l’extérieur.
Utilisation du caisson
G Prise de vue
L’image s’enregistre sur la cassette.
1 Réglez le commutateur POWER sur “ON”.
Le caméscope se met sous tension et le témoin CAMERA s’allume.
2 Appuyez sur la touche START/STOP pour démarrer
l’enregistrement.
Pour faire une pause
Appuyez sur START/STOP. Appuyez de nouveau sur la touche pour
continuer.
Pour arrêter l’enregistrement
Appuyez sur la touche START/STOP et réglez le commutateur POWER sur
“OFF”.
H Prise de vue avec l’écran LCD
Vous pouvez filmer en regardant l’image se reflétant dans le miroir.
1 Faites coulisser le viseur à miroir en maintenant la marque
OPEN et ouvrez-le.
2 Ouvrez les volets et insérez les saillies dans chaque orifice.
Pour refermer le viseur à miroir
Détachez les parties saillantes des deux volets et fermez d’abord le volet
inférieur.
Zoom
•Appuyez sur le côté “W” de la touche pour élargir l’angle de prise de vue.
•Appuyez sur le côté “T” de la touche pour une prise de vue au téléobjectif.
Appuyez légèrement sur la touche pour un zoom relativement lent.
Remarques sur la prise de vue
•Si vous laissez le caméscope 5 minutes ou plus en mode de veille avec une
cassette à l’intérieur, le caméscope s’arrête automatiquement pout
protéger la batterie et la bande de l’usure. Pour réactiver le mode de veille,
réglez le commutateur POWER sur “OFF” puis sur CAMERA.
•Le commutateur POWER du caisson a priorité sur le commutateur
POWER du caméscope.
•Pendant la prise de vue avec l’écran LCD orienté vers l’extérieur, le
compteur n’apparaît pas.
I Enregistrement d’une image fixe
L’image fixe est enregistrée sur le “Memory Stick”.
1 Faites glisser le commutateur POWER dans le sens de la flèche
de sorte que le témoin MEMORY s’allume.
2 Appuyez brièvement sur la touche PHOTO.
La marque verte cesse de clignoter et reste allumée. L’image peut alors être
enregistrée.
3 Appuyez à fond sur la touche PHOTO.
L’image qui apparaît lorsque vous appuyez à fond sur la touche PHOTO est
enregistrée sur le “Memory Stick”.
Vous pouvez aussi enregistrer une image fixe lorsque le témoin CAMERA
est allumé.
Remarque
Lorsque vous utilisez le caisson étanche, vous ne pouvez pas utiliser les
fonctions suivantes : NightShot et Enregistrement au flash.
J Enregistrement d’images animées sur le
“Memory Stick”
1 Faites glisser le commutateur POWER dans le sens de la flèche
de sorte que le témoin MEMORY s’allume.
2 Appuyez sur la touche START/STOP.
K Utilisation de la télécommande pour la
lecture
Vous pouvez revoir les images sur l’écran LCD en utilisant la
télécommande (fournie avec le caméscope).
Vous n’entendrez pas le son.
1 Faites glisser le commutateur POWER dans le sens de la flèche
de sorte que le témoin VCR s’allume.
2 Appuyez sur N PLAY de la télécommande.
Vous pouvez aussi utiliser la télécommande pour les autres fonctions, par exemple
STOP, REW et FF. Le capteur se trouve à l’avant, au bas du caisson.
Dirigez la télécommande vers le capteur pour activer les différentes commandes.
Remarque
Sur le miroir, l’image apparaît inversée.
L Retrait du caméscope
Avant d’ouvrir le caisson, séchez-le bien et essuyez-vous. Ne laissez pas
tomber d’eau sur le caméscope.
1 Mettez le commutateur POWER en position “OFF”.
2 Relâchez les boucles et ouvrez la partie arrière. (Voir
l’illustration E-2)
3 Débranchez le fiche de télécommande de la prise   LANC, en
débranchez ensuite la fiche de microphone de la prise A/V.
Remarque
Débranchez la fiche avant de sortir le caméscope pour ne pas
endommager la fiche ni le caméscope. Tirez sur la fiche et non pas sur le
cordon.
4 Sortez le sabot de montage du caméscope.
Tenez le sabot de montage par les boutons latéraux et appuyez sur les boutons
pour extraire le caméscope.
5 Détachez le sabot de montage.
Cause
La fiche du microphone
n’est pas branchée.
• Les boucles ne sont pas
serrées.
• Le joint d’étanchéité
n’est pas correctement
installé.
• Le joint d’étanchéité est
abîme ou craquelé.
• La batterie est épuisée.
• La fiche de
télécommande n’est
pas raccordée.
• La bande est finie.
• Le taquet de sécurité de
la cassette et du
“Memory Stick” sont
en position
d’interdiction
d’enregistrement.
• Le “Memory Stick” est
plein.
Solution
Branchez-la sur la prise A/V
du caméscope.
• Serrez les boucles jusqu’à ce
qu’elles s’encliquettent.
• Insérez correctement le joint
d’étanchéité dans la
rainure.
• Remplacez le joint
d’étanchéité.
• Chargez complètement la
batterie.
• Raccordez-la à la prise
 LANC du caméscope.
• Rembobinez la bande ou
utilisez une autre cassette.
• Faites glisser le taquet de
sécurité ou installez une
nouvelle cassette et un
nouveau “Memory Stick”.
• Insérez un autre “Memory
Stick” et effacez les données
inutiles du “Memory Stick”.
Cause
The microphone plug is not
connected.
• The buckles are not
fastened.
• The waterproof gasket is
not set correctly .
• There are scratches or
cracks on the waterproof
gasket.
• The battery pack is run
out.
• The remote control plug is
not connected.
• The tape has run out.
• The safety tab on the
cassette and the “Memory
Stick” is set to
unrecordable position.
• The “Memory Stick” is
full.
Corrective Actions
Connect it to A/V jack on
the video camera recorder.
• Fasten the buckles until
they click.
• Put the gasket in the
groove evenly.
• Replace the gasket with a
new one.
• Charge the battery pack
fully.
• Connect it to   LANC
jack on the video camera
recorder.
• Rewind the tape or use a
new one.
• Slide the safety tab or
install a new cassette tape
and a new “Memory
Stick”.
• Insert another “Memory
Stick” or erase unneeded
data from the “Memory
Stick”.
3-076-894-11(2)
SPK-IP55
Sony Corporation © 2002  Printed in Japan
Sports Pack
Eng ish
English
Français
Preparing
For details, please refer to the operating instructions supplied with your
video camera recorder.
D Preparing the Video Camera Recorder
1 Remove the wrist strap, filter or conversion lens from the video
camera recorder.
2 Install the battery pack.
3 Insert the cassette tape and the “Memory Stick”.
Unlock the safety tab on the “Memory Stick” and the cassette tape, and make them
possible to record images.
Be sure that a tape and the “Memory Stick” has enough space to record images.
4 Attach the reflex prevention ring.
The reflex prevention ring to a certain extent prevents reflection of the lens ring
section of your video camera recorder on the front glass.
5 When shooting with the LCD screen, turn the LCD panel over
and move back to the video camera recorder with the LCD
screen facing out.
6 Set the functions, such as focusing and lightning, to AUTO.
E Installing the Video Camera Recorder
Turn the POWER switch of the video camera recorder to “OFF” (CHG), and
leave the POWER switch of the sports pack “OFF”.
1 Attach the camera mounting shoe.
Use the metal parts of shoulder strap as shown in the illustration.
2 Release the buckles.
1
Slide the unlock button in the direction of the arrow, and release the buckles.
2
Open the rear body.
Coat the front glass with anti-fogging lens solution.
Coat the surface of the glass on the front of the sports pack with the supplied
anti-fogging lens solution.
3 Remove foreign materials.
Remove foreign materials such as dust, sand or hair from the waterproof gasket,
the groove and any surface it touches. Then, put the grease evenly on the water-
proof gasket.
If the body is closed with such materials present, these areas may be damaged and
water may leak in.
4 Installing the video camera recorder.
Align the camera mounting shoe with the guide on the front body.
Insert the video camera recorder by pushing the rear of the camera mounting shoe
until it clicks. Check the knob on each side of the camera mounting shoe to ensure
that it locked properly. Be careful not to pinch the cords then.
Note
Be sure to keep the video camera recorder horizontal when installing it.
Inserting the video camera recorder into the front body vertically may
damage the camera mounting shoe and the front body.
5 Connect the plugs to the each jacks of the video camera
recorder. (See illustration E-5)
1
Connect the remote control plug to 
 LANC jack.
2
Then, connect the microphone plug to A/V jack.
6 Close the rear body.
Then secure the rear body, and fasten the buckles until they click.
Note
• Be careful not to pinch the cords when closing the rear body.
• When the video camera recorder is put into the sports pack, the center
of the lens may shift with respect to the front glass of the sports pack.
This will cause no problems when revording.
F Preparing the Sports Pack
1 Adjust the grip strap.
Holding the sports pack so that the tips of your finger can easily touch the POWER
switch, START/STOP button and ZOOM button, pull the strap to adjust its length.
2 Attach the shoulder strap.
The SONY mark should be on the outside.
Using the Sports Pack
G Recording
A picture is recorded on the tape.
1 Turn the POWER switch to “ON”.
It turns on the power, and lights the CAMERA lamp.
2 Press START/STOP button to start recording.
To stop recording
Press START/STOP. Press again to resume recording.
To finish recording
Press START/STOP button then turn the POWER switch to “OFF”.
H When Shooting with the LCD Screen
You can shoot with the reflection in the mirror.
1 Slide the mirror hood while holding the OPEN mark and open it.
2 Open the wings and insert the projections into each hole.
To close the mirror hood
Undo the projections on the both wings, and close the lower wing first.
Zooming
•Keep the W side pressed for wide-angle.
•Keep the T side pressed for telephoto.
Press it gently for a relatively slow zoom.
Notes on recording
•If you leave the video camera recorder for 5 minutes or more with a
cassette inserted in Standby mode, the video camera recorder goes off
automatically. This prevents battery and tape wear. To resume Standby
mode, turn the POWER switch to “OFF” and then turn it to CAMERA
again.
•The POWER switch of the sports pack has priority over the POWER
switch of the video camera recorder.
•During recording when the LCD screen is facing out, the counter does not
appear.
I Recording a Still Picture
The still picture is recorded on the “Memory Stick”.
1 Slide the POWER switch along following the arrow, and light
the MEMORY lamp.
2 Press PHOTO button softly.
The green mark stops flashing , then lights up. This makes it possible to record a
Still Picture.
3 Press PHOTO button deeper.
The image when you pressed PHOTO button deeper will be recorded on the
“Memory Stick”.
Above-stated operation
You can also record a still picture by lighting CAMERA lamp.
Note
While using the sports pack, the following operations are not available;
NightShot and recording with the flash.
J Recording moving pictures on the
“Memory Stick”
1 Slide the POWER switch along following the arrow, and light
the MEMORY lamp.
2 Press START/STOP button.
K Playing Back with the Remote Commander
You can play back pictures on the LCD screen, using the Remote
Commander (supplied with your video camera recorder).
You cannot hear the sound.
1 Slide the POWER switch along following the arrow, and light
the VCR lamp.
2 Press N PLAY on the remote.
Use the remote commander for all other functions including STOP, REW and FF.
The remote sensor is located on the front lower part of the sports pack.
Point the remote commander toward the remote sensor to control the video camera
recorder.
Note
The picture on the mirror looks turned sideways.
L Removing the Video Camera Recorder
Before opening the sports pack, wipe moisture off the sports pack and
yourself. Do not allow water on the video camera recorder.
1 Turn the POWER switch to “OFF”.
2 Release the buckles, and open the rear body. (See illustration
E-2)
3 Disconnect the remote control plug from the   LANC
jack, and the microphone plug from the A/V jack.
Note
Be sure to disconnect the plugs by holding the plug part, not the cord
part before taking out the video camera recorder. Otherwise, the plugs
and the video camera recorder may be damaged.
4 Pull out the camera mounting shoe.
Holding the camera mounting shoe by the knobs on both sides of it, press the
knobs and extract the video camera recorder.
5 Detach the camera mounting shoe.
Owner’s Record
The model and serial numbers are located inside of the unit. Record the
serial number in the space provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
Model No. SPK-IP55   Serial No.
E
1
4
5
1
2
4
Use metal
parts of
shoulder belt.
Utilisez les
éléments
métalliques
de la
bandoulière.
Camera mounting shoe
Sabot de montage du
caméscope
Body
Corps
Guide
Guide
I
K
1
1
H
L
F
2
2
Telephoto
Télé
Wide-angle
Grand angle
Slide the mirror hood while holding the OPEN mark
and open it.
Tirez l’écran à miroir tout en tenant la marque OPEN
et ouvrez-le.
Zooming
Zoom
1
2
1
3
4
2
G
1
2
4
3
1
2
OPEN
5
J
2
Groove
Rainure
Tapering side up
Côté effilé vers le
haut
B
C
Waterproof gasket
Joint d’étanchéité
*Spacer
*Entretoise
Mirror hood
Ecran à
miroir
Hook for shoulder strap
Crochet de bandoulière
Camera mounting shoe
Sabot de montage du
caméscope
Microphone plug
Fiche de microphone
Remote plug
Fiche de
télécommande
**Plug holder
**Porte-fiche
* Remove the spacer when the unit is in use.
* Enlevez l’entretoise lorsque vous utilisez le caisson.
** Insert the remote plug in the plug holder when the unit is not in use.
Remove the plug and then take out the camera mounting shoe.
** Insérez la fiche dans le porte-fiche lorsque vous n’utilisez pas le caisson.
Enlevez la fiche et sortez le sabot de montage du caméscope.
2
 A/V Jack
Prise A/V
1
   LANK Jack
Prise   LANC
5
Buckle
Boucle
Rear body
Partie arrière
START/STOP button
Touche START/STOP
POWER switch
Commutateur POWER
Grip strap
Sangle
Tripod mounting hole
Filetage de trépied
PHOTO button
Touche PHOTO
Mode lamp
Témoin de mode
Front body
Partie avant
Zoom button
Touche de
zoom
Front glass
Vitre avant
Stereo microphone
Microphone stéréo
Hook for shoulder
strap
Crochet de bandoulière
D
1
2