Sony super had ccd ssc-cd49p User Manual

B

7

1: INT/LL (line lock) switch (Initial setting: LL)

Use this switch to set the camera synchronization mode to INT
(internal) or LL (line lock, Only when the power is AC 24 V).

2: AGC (automatic gain control) switch (Initial setting: ON)

Set to ON to adjust the gain of the video amplifier automatically
according to the brightness of the object.

BLC (backlight compensation) switch (Initial setting: OFF)

Use this switch to adjust the exposure to compensate for situations
where the subject is lit from behind.

When BLC switch is set to ON, a hunting may be generated due to a
picture. In this case, set BLC switch to OFF.

DynaView switch (Initial setting: OFF)

Set this switch to ON to active the DynaView function.

4: ATW switch (Initial setting: ATW)

ATW: Automatic adjusting function of the white balance, effective for
use under special light like a sodium lamp.

ATW Pro: Automatic adjusting function of the white balance according
to the color temperature based on a fluorescent light, incandescent
lighting, or  natural light.

5-7: Not used with this unit.

8

Use this screw to adjust the vertical phase of cameras synchronized
by LL.

9

0

Make sure to tighten the screws securely when installing the camera.

qa

First loose the screw and face the camera head to the desired
direction, then tighten the screw to fix it.

qs

Connect to a video input connector of a monitor . You can adjust the
camera while looking at the image on the monitor. After adjusting the
camera, disconnect the cable.

C

qd

Outputs a composite video signal. Connect to a composite video input
connector of a video monitor, VCR, etc (

).

qf

Connect to a 24V AC or 12V DC power supply system (

). The

connector tip is a quick-disconnect type. You can screw the cables in
the tip.

qg

(continued on the reverse side)

3-113-373-01 (1)

 2007 Sony Corporation  

Printed in China

Before operating the unit, please read this manual thoroughly and
retain it for future reference.

This is a dome-shaped color video camera for which the 1/3 type Super
HAD CCD

®

 has been adopted. It has the following features:

• Manual setting of the camera direction – panning, tilting and rotating
• Vari-focal auto iris lens as standard equipment. The focal length of the

lens is from 2.8 mm to 10 mm.

• High quality CCD and clear dome cover enable high sensitivity.
• Backlight compensation through the center measurement (SSC-CD45/

CD45P only).

• Wide dynamic range (128 times wider than normal) using DynaView

technology (SSC-CD49/CD49P only)

• Automatic white balance tracking and adjustment (ATW/ATW-PRO)
• AC 24 V / DC 12 V power supply system
• Line lock function (24 V AC)

• Super HAD CCD

®

 is a registered trademark of Sony Corporation.

• DynaView

TM

 is a registered trademark of Sony Corporation.

Do not shoot an extremely bright object (an illumination, the sun, etc.).
Also, avoid operating or storing the camera in the following locations, as
these can be a cause of a malfunction.
• Extremely hot or cold places (Operating temperature: –20 °C to

+50 °C [–4 °F to 122 °F])

• Exposed to direct sunlight for a long time, or close to heating

equipment (e.g., near heaters)

• Close to sources of strong magnetism
• Close to sources of powerful electromagnetic radiation, such as radios

or TV transmitters

• Locations subject to vibration or shock
• Humid or dusty locations
• Locations exposed to rain
• Locations under the influence of fluorescent light or reflection of a

window

• Under an unsteady light (the image will flicker.)

To prevent heat buildup, do not block air circulation around the camera.

When transporting the camera, repack it as originally packed at the
factory or in materials of equal quality.

• Use a blower to remove dust from the lens.
• Use a soft, dry cloth to clean the external surfaces of the camera.

Stubborn stains can be removed using a soft cloth dampened with a
small quantity of detergent solution, then wipe dry.

• Do not use volatile solvents such as alcohol, benzene or thinners as

they may damage the surface finishes.

Laser beams may damage a CCD. You are cautioned that the surface of a
CCD should not be exposed to laser beam radiation in an environment
where a laser beam device is used.

The following phenomena may appear on the monitor screen while you
are using a CCD color video camera. These phenomena stem from the
high sensitivity of the CCD image sensors, and do not indicate a fault
within the camera.

A “smear” may appear to extend vertically from very bright subjects, as
shown below.

                           

This phenomenon is common to CCD imaging elements using an interline
transfer system, and is caused when electric charge induced by infrared
radiation deep within the photo sensor is transferred to the resistors.

When shooting fine stripes, straight lines or similar patterns, the lines may
become slightly jagged.

A CCD image sensor consists of an array of individual picture elements
(pixels). A malfunctioning sensor element will show up
as a single pixel blemish in the image. This is generally not a problem.

When you shoot a poorly illuminated object at a high temperature, small
white dots may appear all over the entire screen image.

The figure shows the camera without the dome casing and slit cover.

A

1

When you wire indoors, cut this part with a nipper or similar and feed
the cable through it.

Take care not to trap the cable between the camera and ceiling or the wall.
If the cable is trapped, it may break and cause a fire or electric shock.

2

3

4

Loosen this screw before adjusting the zoom and focus, then tighten it
to fix the lens position. The screw can be inserted at one of three
points.

5

Turn this ring to adjust the field of view.

6

Turn this ring to adjust the focus.

The model and serial numbers are located on the bottom. Record these
numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer
regarding this product.

Model No. 

 Serial No. 

This installation should be made by a qualified service person and should
conform to all local codes.

A readily accessible disconnect device shall be incorporated in the
building installation wiring.

Instructions for installing the equipment on the ceiling or the wall:
After the installation, ensure the connection is capable of supporting at
least a force of 50 Newtons (N) downwards.

The rating label is located on the bottom.

The SSC-CD45/CD49 operates on 24V AC or 12V DC.
The SSC-CD45/CD49 automatically detects the power.
Use a Class 2 power supply which is UL Listed (in the U.S.A) or CSA-
certified (in Canada).

The SSC-CD45/45P/CD49/49P operates on 24V AC or 12V DC.
The SSC-CD45/45P/CD49/49P automatically detects the power.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.

You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order
to comply with the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.

This is a Class A product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.
In the case that interference should occur, consult your nearest
authorized Sony service facility.

The electromagnetic fields at specific frequencies may influence the
picture of the unit.

A

B

Upper

Lower

No.

1

2

3

4

Switch

INT/LL

AGC

BLC (SSC-CD45/CD45P)
DynaView (SSC-CD49/49P)

ATW

Upper (ON)

ON

ATW Pro

Lower

INT

OFF

Position

5

6

4

1

3

2

9

7

8

0

qa

qs

qf

qd

qg

C

                               

Video monitor screen

Pale vertical smear

Very bright subject (such as an
electric lamp, fluorescent lamp,
sunlight, or strong reflected light)