Sony VGPBPSC27 User Manual

Page of 2
安全のために
電気製品は安全のための注意事項を守らないと、火災や人身事故になるこ
とがあります。事故を防ぐために次のことを必ずお守りください。
安全のための注意事項を守る
この取扱説明書の注意事項をよくお読みください。お読みになったあとは、
いつでも見られるところに必ず保管してください。
万一、異常が起きたら
変な音・においが
したら、
 
煙が出たら、
 
異常に温度が
 
上がったら
すぐにバッテリーをはずし、
VAIO
カス
タマーリンク修理窓口に修理をご依頼
ください。
警告表示の意味
取扱説明書および製品では、次のような表示をしています。表示の内容をよく
 
理解してから本文をお読みください。
この表示の注意事項を守らないと、火災・感電・破裂などにより
 
死亡や大けがなど人身事故が生じます。
この表示の注意事項を守らないと、火災や感電などにより
 
死亡や大けがなどの人身事故につながることがあります。
この表示の注意事項を守らないと、感電やその他の事故により
 
けがをしたり周辺の家財に損害を与えたりすることがあります。
注意を促す記号
下記の注意事項を守らないと
火災・
 
破裂
により
死亡
大けが
などの
 
人身事故が生じます。
 
指定された充電方法以外で充電しない。
 
火の中に入れない。ショートさせたり、分解しない。電子レンジやオー
ブンで加熱しない。
 
コインやヘヤーピンなどの金属類と一緒に携帯、保管するとショートす
ることがあります。
 
火のそばや炎天下などで充電したり、放置したりしない。
 
バッテリーパックに衝撃を与えない。
 
落とすなどして強いショックを与えたり、重いものを載せたり、圧力を
かけないでください。故障の原因となります。
 
性能が低下したバッテリーを使わない。
 
バッテリー駆動時間が短くなった場合には、純正の新しいバッテリーと
交換してください。
 
以下の場合の安全性は保証できません。
 
– 
指定された機種以外に使用した。
 
– 
分解、改造を行って使用した。
 
画鋲などの突起物でささない。
下記の注意事項を守らないと
火災
などに
 
より
死亡
大けが
の原因となります。
バッテリーを廃棄する場合は、一般ごみに混ぜて捨てない。
バッテリーは、ゴミ収集作業などで衝撃や圧力が加わり、漏液・発熱・発火・
爆発・破裂などの危険があります。廃棄する場合は、リサイクル協力店へお
持ちください。
または、地方自治体の条例などに従ってください。
下記の注意を守らないと
けが
をしたり
 
周辺の
家財
損害
を与えたりすることが
 
あります。
 
パーソナルコンピューターに取り付けて持ち運ぶときは、バッテリーパッ
ク部分を持たない。
 
パーソナルコンピューターの液晶ディスプレイを開くときは、バッテリー
パック部分を持たない。
バッテリーパック部分を持つと故障の原因になることがあります。
AC
電源の遮断について
電源から切り離すためには、プラグをコンセントから抜く必要があります。
不具合を感じた場合はすぐにコンセントからプラグを抜けるように、
AC
ダプターは、コンセントの近くでお使いください。
AC
アダプターについて
AC
アダプターは、ソニー純正の指定品のものをお使いください。
お使いになる前に
本リチャージャブルバッテリーパックは、ソニーパーソナルコンピューター
専用のエクステンドバッテリーです。機種によっては使えないものもあり
ます。お使いになる前に、お手持ちの機器をお確かめください。
使いかたについては、パーソナルコンピューター本体に付属の取扱説明書
または電子マニュアルもあわせてご覧ください。
使いかた
本バッテリーパックを取り付けるには
ご注意
本バッテリーパックの取り付け/取りはずしは、パーソナルコンピューターの電源を
切り、液晶ディスプレイを閉じてから行ってください。
1
 
パーソナルコンピューターにプライマリーバッテリーが装着され
ていることを確認する。
プライマリーバッテリーが装着されていないと、本バッテリーパック
は認識されません。
2
 
パーソナルコンピューターのカバー()をはずす。
ご注意
はずしたカバーは、バッテリーパック()に取り付けて保管してください。
3
 
バッテリーパックのロックレバーが図の位置にあることを確認し
()、ロック金具をパーソナルコンピューターのスリット(溝)
()
に入れて、図のように置く()。
4
 
下図の部分を軽く押し、バッテリーパックとパーソナルコンピュー
ターの端子を接続する。
5
 
バッテリーパックにある
2
か所のネジをしめる。
6
 
ロックレバーを矢印の方向(
LOCK
側)へずらしてバッテリーパッ
クを固定する。
バッテリーパックを取りはずすには
1
 
ロックレバーを
LOCK
と反対側(取り付け手順
3
の)にずらす。
2
 
バッテリーパックにある
2
か所のネジをゆるめる。
3
 
バッテリーパックのリリースレバーを矢印の方向にずらしたまま
()バッテリーパックに指をかけ、矢印の方向に軽く持ち上げて
取りはずす()。
バッテリーアダプターを使って充電するには
ご注意
お使いのパーソナルコンピューターに付属されている電源コードと
AC
アダプターをお
使いください。
1
 
バッテリーパックをパーソナルコンピューターから取りはずす。
2
  AC
アダプターをバッテリーアダプターに接続する。
3
 
バッテリーアダプターをバッテリーパックの端子に差し込む。
のラインに沿って、バッテリーアダプターを取り付けてください。
充電が始まり、
CHARGE
ランプ()が赤く点灯します。充電が終了す
るとランプは消灯します。
 
ヒント
  CHARGE
ランプが点滅しているときは、バッテリーエラーです。手順
2
からや
り直してください。
 
バッテリーパックはバッテリーアダプターを使わずに、パーソナルコンピュー
ターに取り付けた状態でも充電できます。
バッテリーアダプターを取りはずすには
バッテリーアダプターのリリースボタンを押しながら()取りはずしてく
ださい()。
主な仕様
バッテリーパック
使用電池
 
リチウムイオン二次電池
公称電圧
 
11.1 V DC
容量
 
4,400 mAh
外形寸法
 
327.6
(幅)
 
×
 7.6
(高さ)
 
×
 185.3
(奥行き)
mm
質量
 
490 g
バッテリーアダプター
入力
 
DC 19.5 V , 3.3 A
外形寸法
 
76.0
(幅)
 
×
 65.0
(高さ)
 
×
 14.7
(奥行き)
mm
質量
 
49 g
その他
動作温度
 
℃∼
35 
℃(温度勾配
10 
℃/時以下)
動作湿度
 
20%
80%
(結露のないこと)ただし
35 
℃におけ
る湿度は
65%
以下(湿球温度
29 
℃以下)
保存温度
 
20 
℃∼+
60 
℃(温度勾配
10 
℃/時以下)
保存湿度
 
10%
90%
(結露のないこと)ただし
60 
℃におけ
る湿度は
20%
以下(湿球温度
35 
℃以下)
付属品
 
バッテリーアダプター(
VGP-BC10
1
 
取扱説明書(
1
仕様および外観は、改良のため予告なく変更することがありますが、ご了
承ください。
使用上のご注意
 
端子をキーホルダーなどの金属類でショート(短絡)させないでください。
 
高温になった車の中や炎天下など、
60 
℃以上になるところに放置しない
でください。
 
水にぬらさないでください。
 
落としたり重いものを載せたりしないでください。本バッテリーパック
に強いショックを与えたり、圧力をかけたりしないでください。
 
本バッテリーパックやパーソナルコンピューターの故障の原因となるこ
とがあります。
バッテリーの放電について
バッテリーは充電後、使用していない場合でも、少量ずつ自然に放電する
ため、長時間放置した場合、バッテリー駆動時間が短くなる場合があります。
使用前には、再度、充電することをおすすめします。
バッテリーの性能低下と交換について
バッテリーは、充電回数、使用時間、保存期間に伴い少しずつ性能が低下
していきます。このため、充分に充電を行ってもバッテリー駆動時間が短
くなったり、寿命で使えなくなることがあります。バッテリー駆動時間が
短くなってきた場合には、弊社指定の新しいバッテリーと交換してください。
バッテリーの交換に関しご不明な点などがございましたら、
VAIO
カスタ
マーリンクまでお問い合わせください。
充電式電池の収集・リサイクルについて
リチウムイオン電池は、リサイクルできます。不要になったリ
チウムイオン電池は、金属部にセロハンテープなどの絶縁テー
プを貼って充電式電池リサイクル協力店へお持ちください。
充電式電池の収集・リサイクルおよびリサイクル協力店に関す
る問い合わせ先:有限責任中間法人
 JBRC
ホームページ
 http://www.jbrc.net/hp/contents/index.html
English
WARNING
To reduce the risk of fire or electric shock, do not expose this 
apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing 
to qualified personnel only.
Owner’s Record
The model number and serial number are located on the bottom of your 
battery pack. Record the serial number in the space provided here. Refer to the 
model and serial number when you call your Sony Service Center.
Model Number: VGP-BPSC27
Serial Number: ______________________
CAUTION
Do not handle damaged or leaking Lithium-Ion batteries.
Danger of explosion if the battery is incorrectly replaced. Replace only with the 
same or equivalent type recommended by the manufacturer. Discard used 
batteries according to the manufacturer’s instructions.
The battery pack may present a fire or chemical burn hazard if mistreated.
Do not crush, disassemble, heat above 60 °C (140 °F) or incinerate.
Keep away from children.
Dispose of used batteries promptly and properly.
Do not short-circuit the metal terminals of the battery pack or wet them with 
any liquid, for example, water, coffee, or juice.
Use your product only with the AC adapter and power cord supplied with your 
personal computer.
The socket-outlet shall be installed near the equipment and shall be easily 
accessible. 
To disconnect it completely, unplug the AC adapter or the power cable from 
mains.
For customers in the USA and Canada
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable.
You can help preserve our environment by returning your used 
rechargeable batteries to the collection and recycling location 
nearest you.
For more information regarding recycling of rechargeable batteries, call toll 
free 1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking Lithium-Ion batteries.
For customers in the USA
The following FCC statements apply only to the version of this model 
manufactured for sale in the USA. Other versions may not comply with FCC 
technical regulations.
This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more 
of the following measures:
  Reorient or relocate the receiving antenna.
  Increase the separation between the equipment and receiver.
  Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
  Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference 
caused by unauthorized modifications to this equipment. Such modifications 
could void the user’s authority to operate the equipment.
Model No.: VGP-BPSC27 (rechargeable battery pack), and VGP-BC10 (battery 
adapter)
These devices comply with Part 15 of the FCC Rules. Operation is subject to 
the following two conditions:
(1) this device may not cause harmful interference, and
(2)  this device must accept any interference received, including interference 
that may cause undesired operation.
For customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Before use
Before using the battery pack, please read this manual thoroughly and retain it 
for future reference. Do not charge the battery pack in any way other than as 
described in this Operating Instructions or the manuals provided with your 
personal computer, or as designated by Sony in writing.
The Sony VGP-BPSC27 Rechargeable Battery Pack is the extended battery pack 
designed for Sony personal computers. However, it may not be used with some 
models.
How to use
Installing the battery pack
Note
Before installing or removing the battery pack, be sure to turn the power of your personal 
computer off and to close the LCD screen lid first.
1
  Make sure a primary battery pack is installed in your personal 
computer.
If it is not installed, the battery pack cannot be recognized.
4-291-789-01 (1)
©2011 Sony Corporation / Printed in China
取扱説明書 / Operating Instructions / Mode d'emploi / 
Manual de instrucciones / Manual de instruções
Rechargeable Battery Pack
VGP-BPSC27
お買い上げいただきありがとうございます。
電気製品は安全のための注意事項を守らないと、火災や人身事故になること
があります。
この取扱説明書には、事故を防ぐための重要な注意事項と製品の取り扱いかたを示しています。
この取扱説明書をよくお読みのうえ、製品を安全にお使いください。
お読みになったあとは、いつでも見られるところに必ず保管してください。
2
  Remove the cover () installed on your personal computer.
Note
Be sure to attach the removed cover to the battery pack () to keep it for future use.
3
  Make sure the battery lock latch of the battery pack is set to 
the unlock position (), and insert the projections () of the 
battery pack into the holes on the bottom of your personal 
computer, and then lower it down in place ().
4
  Carefully press the battery pack as illustrated below to engage 
the connectors of the battery pack and your personal 
computer.
5
  Tighten the two screws of the battery pack.
6
  Slide the battery lock latch in the direction of the arrow (LOCK 
position) to secure the battery pack.
To remove the battery pack
1
  Slide the battery lock latch away from the LOCK position (step 
3-) of the installation procedure.
2
  Loosen the two screws of the battery pack.
3
  Hold the battery release latch in the direction of the arrow (
and carefully lift the battery pack away from your computer in 
the direction of the arrow ().
Charging the battery pack using a battery adapter
Note
Use the power cord and AC adapter supplied with your personal computer.
1
  Remove the battery pack from your personal computer.
2
  Connect the AC adapter to the battery adapter.
3
  Insert the battery adapter into the connector of the battery 
pack.
Install the battery adapter, aligning the  area.
When charging starts, the CHARGE indicator () lights up red. When 
charging is completed, the indicator turns off.
Hints
  If the CHARGE indicator () flashes, a battery error may have occurred. Start 
again from the step 2.
  The battery pack can also be charged by installing your personal computer, 
without the battery adapter.
To remove the battery adapter
Push and hold the release buttons () of the battery adapter, and remove the 
adapter from the battery pack ().
Specifications
Battery pack
Battery used 
Lithium-ion type battery
Mean output voltage 
11.1 V DC
Capacity 
4,400 mAh
Maximum charge current  3.08 A
Maximum charge voltage  12.54 V
Dimensions 
Approx. 327.6 × 7.6 × 185.3 mm 
(12.9 × 0.3 × 7.3 inches) (w/h/d)
Mass 
Approx. 490 g (17.3 oz)
Battery adapter
Input 
DC 19.5 V, 3.3 A
Dimensions 
Approx. 76.0 × 65.0 × 14.7 mm  
(3.0 × 2.6 × 0.6 inches) (w/h/d)
Mass 
Approx. 49 g (1.8 oz)
日本語
¡IMPORTANTE!
POR FAVOR LEA DETALLADAMENTE ESTE MANUAL DE INSTRUCCIONES ANTES DE 
CONECTAR Y OPERAR ESTE EQUIPO.
RECUERDE QUE UN MAL USO DE SU APARATO PODRÍA ANULAR LA GARANTÍA.
Other
Operating temperature 
5 °C to 35 °C (41 °F to 95 °F ) 
(temperature gradient less than 10 °C (18 °F ) /hour)
Operating humidity 
20% to 80% (not condensed), provided that humidity 
is less than 65% of 35 °C ( 95 °F ) 
(hygrometer reading at less than 29 °C (84 °F))
Storage temperature 
–20 °C to +60 °C (–4 °F to +140 °F ) 
(temperature gradient less than 10 °C (18 °F ) /hour)
Storage humidity 
10% to 90% (not condensed), provided that humidity 
is less than 20% of 60 °C (140 °F) 
(hygrometer reading at less than 35 °C (95 °F))
Supplied accessories 
Battery adapter (VGP-BC10) 
Operating Instructions
Design and specifications are subject to change without notice.
Notes on use
  Keep the battery pack dry.
  Do not drop the battery pack or place heavy objects on it. Do not apply 
strong pressure or physical shock to the battery pack. These actions may 
cause the battery pack or the personal computer to malfunction.
  Do not hold the personal computer by its battery pack when carrying it or 
opening the display panel, as this may result in damage.
  If, after fully charging the battery pack, the battery power is still low, the 
battery pack may be reaching the end of its life and should be replaced.
  Do not puncture with a sharp object, such as a drawing pin, etc. Heat or 
flammable gas may be generated.