Sony VPL-FX40 User Manual
25
Other Functions
C
o
n
v
en
ient
Fun
ient
Fun
c
tions
Other Functions
If you will be using a circuit breaker to turn
the power for the entire system on and off,
set the direct power on function to “On.”
When you turn off the power, you can also
just unplug the power cord without pressing
the ?/1 key. The internal circuitry will cause
the fan to automatically operate for a certain
time even after the power cord is removed.
the power for the entire system on and off,
set the direct power on function to “On.”
When you turn off the power, you can also
just unplug the power cord without pressing
the ?/1 key. The internal circuitry will cause
the fan to automatically operate for a certain
time even after the power cord is removed.
However, if the projector has been on for less
than 15 minutes, the fan might not turn enough
as a result of inadequate charging. In that case,
follow the procedure for turning off the power
as described in “Turning Off the Power” on
page 21.
than 15 minutes, the fan might not turn enough
as a result of inadequate charging. In that case,
follow the procedure for turning off the power
as described in “Turning Off the Power” on
page 21.
If you are leaving the conference room
immediately, turn the projector off, and then,
you can unplug the AC power cord. After the
AC power cord is unplugged, the fan runs for
a certain time automatically.
immediately, turn the projector off, and then,
you can unplug the AC power cord. After the
AC power cord is unplugged, the fan runs for
a certain time automatically.
However, if the projector has been on for less
than 15 minutes, the fan might not turn enough
as a result of inadequate charging. In that case,
follow the procedure for turning off the power
as described in “Turning Off the Power” on
page 21.
than 15 minutes, the fan might not turn enough
as a result of inadequate charging. In that case,
follow the procedure for turning off the power
as described in “Turning Off the Power” on
page 21.
To freeze the image projected
(Freeze function)
(Freeze function)
Press the FREEZE key. “Freeze” appears
when the key is pressed. This function works
when a signal from a computer is input.
To restore the original screen, press the
FREEZE key again.
when the key is pressed. This function works
when a signal from a computer is input.
To restore the original screen, press the
FREEZE key again.
When you are using the network
presentation function to project the picture
from a computer, you can perform some
operations for a slide show using a
presentation tool (not supplied). The
following keys on the presentation tool are
usable.
presentation function to project the picture
from a computer, you can perform some
operations for a slide show using a
presentation tool (not supplied). The
following keys on the presentation tool are
usable.
* Even if the network presentation function is
not used, the LASER key can be used.
• If there is any obstruction between the
presentation tool and the remote control
detector on the projector, the presentation
tool may not function properly.
detector on the projector, the presentation
tool may not function properly.
• A black screen may not be displayed even if
you press the “B” key depending on the
operating system (OS) of the language of
your computer.
operating system (OS) of the language of
your computer.
• When you use the presentation tool, set “ID
Mode” in the Installation menu to “All” or
“1.”
“1.”
Direct Power On/Off Function
Note
Off & Go Function
Note
Effective Tools for Your
Presentation
Presentation
Controlling the Computer
Using a Presentation Tool,
RM-PJPK1 (not supplied)
(When Using the Network
Presentation Function)
Using a Presentation Tool,
RM-PJPK1 (not supplied)
(When Using the Network
Presentation Function)
Key
Function
LASER
Emits a laser beam.
*
G SLIDE g
Changes the slides in
the forward/backward
direction.
the forward/backward
direction.
B
Displays/cancels a
black screen during the
slide show.
black screen during the
slide show.
Notes