Sony VPL-FX50 User Manual
12
(GB)
Location and Function of Controls
6
TRIG (trigger output) jack (monaural
minijack)
The signal is transmitted from this jack to the
connected equipment whether the projector is on or
off. (This is not a power source for external
equipment.) Approximately 12 V DC signal is output
when the projector power is on. The signal is 0 volt
level output when the projector power is off.
The signal is transmitted from this jack to the
connected equipment whether the projector is on or
off. (This is not a power source for external
equipment.) Approximately 12 V DC signal is output
when the projector power is on. The signal is 0 volt
level output when the projector power is off.
7
CONTROL S/PLUG IN POWER (DC 5V
output) jack (stereo minijack)
Connects to the control S out jacks of the Sony equipment.
Connects to the CONTROL S OUT jack on the supplied
Remote Commander when using it as a wired Remote
Commander. In this case, you do not need to install the
batteries in the Remote Commander, since the power is
supplied from this jack.
Connects to the control S out jacks of the Sony equipment.
Connects to the CONTROL S OUT jack on the supplied
Remote Commander when using it as a wired Remote
Commander. In this case, you do not need to install the
batteries in the Remote Commander, since the power is
supplied from this jack.
8
RS-232C connector (D-sub 9-pin, female)
Connects to a computer to operate the projector from
the computer.
the computer.
9
VIDEO OUT connectors
S VIDEO (mini DIN 4-pin): Used as loop-through
output via the S VIDEO IN connector.
VIDEO (BNC type): Used as loop-through output
via the VIDEO IN connector.
q;
MONITOR OUT connector (HD D-sub 15-pin,
female)
Connects to the monitor input connector on the
monitor. Outputs signals from the selected channel in
the INPUT A (5BNC) or INPUT B (DVI) connector.
This connector does not output any signals from the
DVI connector if the input signal is digital.
Connects to the monitor input connector on the
monitor. Outputs signals from the selected channel in
the INPUT A (5BNC) or INPUT B (DVI) connector.
This connector does not output any signals from the
DVI connector if the input signal is digital.
Connector panel
1
INPUT A 5BNC connectors (R/R-Y/P
R
, G/Y, B/
B-Y/P
B
, SYNC/HD, VD connectors) (BNC type)
Connect to a high-resolution computer or VCR where
signals are transmitted long distances; for example,
when the projector is installed on the ceiling.
According to the connected equipment, computer,
component (R-Y/Y/B-Y), HDTV or DTV signal is
selected.
signals are transmitted long distances; for example,
when the projector is installed on the ceiling.
According to the connected equipment, computer,
component (R-Y/Y/B-Y), HDTV or DTV signal is
selected.
2
INPUT B RGB (DVI) connector
Connect to equipment equipped with the DVI output
(digital or analog RGB) using a commercially
available DVI cable.
(digital or analog RGB) using a commercially
available DVI cable.
3
INPUT C PC CARD slot (Type II)
A wireless LAN PC card or PC memory card can be
attached according to your requirement.
attached according to your requirement.
For details, see “Installing a PC card” on page 16 (GB).
4
INPUT C ETHER connector (10BASE-T)
Connect to a computer on the same LAN with the
LAN cable when you use the networking function of
this projector.
LAN cable when you use the networking function of
this projector.
5
VIDEO IN connectors
Connect to external video equipment such as a VCR.
S VIDEO (mini DIN 4-pin): Connects to the S video
output (Y/C video output) on video equipment.
VIDEO (BNC type): Connects to the composite
video output.
Front
INPUT A
R/R-Y/P
R
INPUT B
RGB (DVI)
RGB (DVI)
INPUT C
ETHER
ETHER
B/B-Y/P
B
G/Y
SYNC/HD
MONITOR OUT
VIDEO IN
VIDEO OUT
S VIDEO
VIDEO
TRIG
RS-232C
PLUG IN POWER
CONTROL S
VD
4
5
6 7
8
9
0
1
3
2