Nokia 6255 Service Manual
6255/6255i6256/6256i (RM-19)
Baseband Description and Troubleshooting
Baseband Description and Troubleshooting
Nokia Customer Care
Page 24
©2005 Nokia Corporation Company Confidential
Issue 2 05/2005
C103
" Boot serial line fail."
Mbus from Prommer->UEME-
>UPP(MbusRx)(SA1)
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
>UPP(MbusRx)(SA1)
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
C104
"MCU ID message sending failed in the Phone."
FbusTx from UPP->UEME->Prommer
C105
"The Phone has not received Secondary boot
codes length bytes correctly."
codes length bytes correctly."
Mbus from Prommer->UEME->UPP(MbusRx)
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
C106
"The Phone has not received Secondary code
bytes correctly."
bytes correctly."
Mbus from Prommer->UEME->UPP(MbusRx)
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
C107
"The Phone MCU can not start Secondary code
correctly."
correctly."
UPP
C586
"The erasing status response from the Phone
informs about fail."
informs about fail."
Flash
C686
"The programming status response from the
Phone informs about fail."
Phone informs about fail."
Flash
Cx81
"The Prommer has detected a checksum error
in the message, which it has received from the
Phone."
in the message, which it has received from the
Phone."
FbusTx from UPP->UEME->Prommer
Cx82
"The Prommer has detected a wrong ID byte in
the message, which it has received from the
Phone."
the message, which it has received from the
Phone."
FbusTx from UPP->UEME->Prommer
A204
Cx83
Cx84
Cx85
"The flash manufacturer and device IDs in the
existing algorithm files do not match with the
IDs received from the target phone."
existing algorithm files do not match with the
IDs received from the target phone."
"The Prommer has not received phone
acknowledge to the message."
acknowledge to the message."
"The phone has generated NAK signal during
data block transfer."
data block transfer."
"Data block handling timeout"
Flash
UPP
VIO/VANA
Signals between UPP-Flash
Mbus from Prommer->UEME->UPP(MbusRx)
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
UPP
VIO/VANA
Signals between UPP-Flash
Mbus from Prommer->UEME->UPP(MbusRx)
FbusRx from Prommer->UEME->UPP
FbusTx from UPP->UEME->Prommer
Cx87
"Wrong MCU ID."
RFClock
UPP(Vcore)
UPP(Vcore)
Startup
for
flashing
for
flashing
Required startup for flashing
Vflash1
VBatt
VBatt
Table 4: Flash Programming Error Codes (Continued)
Error
Description
Not Working Properly