Panasonic BT-LH1700WE User Manual

E-15

The underlined values are factory preset setting values. 

*1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not 

reflected in the sub window. 

*2  When “RGB-COMP.” is selected in “YP

B

P

R

/RGB” in the “INPUT SELECT” menu (

J page E-20), this does not operate.

*3 The following sharpness values can each be set, 

1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, 

 

SHARPNESS H/V : 0)

2) any other input line’s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line’s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is 
displayed in the bottom right when selected. 

*4 When “VAR1”, “VAR2” or “VAR3” is selected, the monitor switches to WB adjustment mode (

J page E-16).

*5 When selecting USER0–63

1) Push [ENTER] (USER changes to blue). 

2) Select 0–63 with [

,

], and push [ENTER]. 

*2

<NORMAL>
<FILM>

*1

Used to select the gamma curve. 
When FILM is selected, 

 mark is displayed in the top 

left of the screen. 

*2

<VARICAM>
<OTHER>

Used to select the type of FILM gamma mode. 
<VARICAM> VARICAM use
<OTHER>

When using other types than VARICAM

<USER0–63>

*5

<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>

Used to select the color temperature. 
<USER0–63>

Adjustable settings 0–63 (color temperature 
around 3000K–9300K)

<D93>

Color temperature around 9300K

<D65>

Color temperature around 6500K

<D56>

Color temperature around 5600K

<VAR1>

WB adjustment mode

*4

<VAR2>

WB adjustment mode

*4

<VAR3>

WB adjustment mode

*4

*2

<HIGH>

*3

<LOW>

Used to select the width of the sharpness edge. 
<HIGH>

Thin edge

<LOW>

Thick edge

*2

<0–30> 

*3

Used to set the sharpness in the horizontal direction. 
When adjusting, the item display moves to the lower part of the 
screen. 

*2

<0–30> 

*3

Used to set the sharpness in the vertical direction. 
When adjusting, the item display moves to the lower part of the 
screen. 

*2

<MODE2>
<MODE1>

Used to set the mode for IP change. 
<MODE2>

Within Field

<MODE1>

Normal mode

*2

<OFF>
<ON>

Used to switch between color and monochrome (MONO). 
<OFF> Color

<ON>

Monochrome

* When this is ON, the picture adjusting knob [CHROMA] setting 

is fixed at 0. 

*2

<OFF>
<ON>

If an Anamo lens has been used on the camera, and input through 
SDI 720/60P, 59.94P, the picture is resized to Anamo size 
magnification. (a vertically compressed signal can be amplified 
vertically and corrected when it is displayed.)

*2

<4:3>
<16:9>

Used for setting the aspect ratio settings when using SD signal 
input. 
<4:3>

4:3 display

<16:9>

16:9 display

*2

<NORMAL>
<UNDER>

Used to set under-scan and normal display. 
<NORMAL>Normal display

<UNDER>Under-scan

*2

<OFF>
<ON>

<OFF> This makes a fluid and smooth contrast obtainable.  

This is especially effective for continuously changing the contrast 
of the source signal or CG signal when the S/N is very high.

<ON>

Noise reduction mode. Depending on the camera, this mode 
can be especially effective for dark scenes. We recommend 
leaving this setting “ON” under normal conditions.