Panasonic cf-18kdqzxvm User Manual
33
T
roub
leshooting
The display is not rotated
automatically by switching
from Laptop mode to Tab-
let mode, or vice versa
The display fails to rotate
even when the rotation but-
ton
automatically by switching
from Laptop mode to Tab-
let mode, or vice versa
The display fails to rotate
even when the rotation but-
ton
is pressed
When the screensaver starts
while the display is rotated,
nothing is displayed on the
screen
while the display is rotated,
nothing is displayed on the
screen
Display Rotation
Confirm that the default angle of each mode is correctly set. (
“Display Rotation”)
Do not switch from Laptop mode to Tablet mode, or vice versa, while Windows is in the
process of switching users with the Fast User Switching function.
process of switching users with the Fast User Switching function.
Close the applications which are open.
Some screensaver types do not display anything on the screen for the first minute or so.
Try changing the screensaver type.
Try changing the screensaver type.
Touch Pad / Digitizer
If you are using an external mouse, ensure that the external mouse has been connected
correctly.
Restart the computer by using the keyboard (Press , U , and select [Restart] with
R ).
If the computer does not respond to keyboard commands, read “No response”
(
correctly.
Restart the computer by using the keyboard (Press , U , and select [Restart] with
R ).
If the computer does not respond to keyboard commands, read “No response”
(
page 34).
Has the Setup Utility been used to set [Touch Pad] to [Enable]?
When external mouse drivers are installed (e.g., IntelliMouse), the touch pad may not be
used.
Has the touch pad driver been properly installed?
Has the Setup Utility been used to set [Digitizer] to [Enable]?
You can use only the pen included with the computer to use the digitizer function.
It is necessary to perform [Calibration] to point correctly with the pen included with the
computer.
When external mouse drivers are installed (e.g., IntelliMouse), the touch pad may not be
used.
Has the touch pad driver been properly installed?
Has the Setup Utility been used to set [Digitizer] to [Enable]?
You can use only the pen included with the computer to use the digitizer function.
It is necessary to perform [Calibration] to point correctly with the pen included with the
computer.
The cursor cannot be con-
trolled properly
trolled properly
Unable to input using the
touch pad
touch pad
Unable to use the digitizer
function
function
Is Adobe Reader installed?
If you have uninstalled Adobe Reader, install using the following procedures.
1
If you have uninstalled Adobe Reader, install using the following procedures.
1
Select [start] - [Run], input [c:\util\reader\AdbeRdr70_enu_full.exe], then select [OK].
Install Adobe Reader by following the instructions on the screen.
Install Adobe Reader by following the instructions on the screen.
Reference Manual
The Reference Manual is
not displayed
not displayed
The orange indicator blinks
Battery cannot be recharged temporarily because the internal temperature of the battery
pack is outside of the acceptable temperature range for recharging. Once the allowable
range requirement is satisfied, charging begins automatically. Your computer can be used
normally in this state.
pack is outside of the acceptable temperature range for recharging. Once the allowable
range requirement is satisfied, charging begins automatically. Your computer can be used
normally in this state.
Battery Indicator (continued)
Cannot log on with the SD
Memory Card
Memory Card
Windows logon user name and password are not set in the SD Memory Card correctly.
Enter the Windows user name and password without using the SD Memory Card.
After logging on, set the same user name and the password on the SD Memory Card and
Windows, using the following operation.
• Change the setting of the SD Memory Card by [SD Card Setup]. (
Enter the Windows user name and password without using the SD Memory Card.
After logging on, set the same user name and the password on the SD Memory Card and
Windows, using the following operation.
• Change the setting of the SD Memory Card by [SD Card Setup]. (
“SD Memory
Card Security Function”)
SD Memory Card