Panasonic cf-27exxxxxx User Manual
26
A port replicator is available as an option (CF-VEB271 or CF-VEB272). This device
eliminates the hassles of having you connect/disconnect the various cables when carry-
ing your computer around and allows a variety of peripherals to be connected including
a headphone or microphone, etc.
eliminates the hassles of having you connect/disconnect the various cables when carry-
ing your computer around and allows a variety of peripherals to be connected including
a headphone or microphone, etc.
The port replicator connects to the expansion bus connector on the back of your com-
puter.
For more detailed information, please refer to the operation manual of the port replicator.
puter.
For more detailed information, please refer to the operation manual of the port replicator.
Port Replicator
Expansion Bus Connector
The serial port B of the port replicator can not be used with the default settings.
Setting the Port Replicator
1
In [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [Mouse] - [AHL/
AR5000 and Digitouch Controllers], add the check mark for [Disable in this hardware
profile] in [Device Usage], press [OK], then press [Close]. Restart the computer.
AR5000 and Digitouch Controllers], add the check mark for [Disable in this hardware
profile] in [Device Usage], press [OK], then press [Close]. Restart the computer.
2
When the message [Press <F2> to enter SETUP] is displayed, press
and then
run the Setup Utility.
3
Select [Advanced] menu and set [Serial Port B] to [Enable] and [Device] to [Port
Replicator].
Press F10 . At the confirmation message, select [Yes] and press Enter . The
computer will reboot.
Replicator].
Press F10 . At the confirmation message, select [Yes] and press Enter . The
computer will reboot.
To be able to use the serial port B of the port replicator, be sure to follow the steps below.
If, however, the situation does not improve, uninstall the touchscreen driver.
below
<Uninstalling the touchscreen driver>
When you want to uninstall the touchscreen driver, follow the steps below.
1
Select [Start] - [Programs] - [Touchscreen] - [Uninstall].
2
Simply follow the on-screen instructions.
<When you use the touchscreen function again>
1
In [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [Mouse]
- [AHL/AR5000 and Digitouch Controllers], delete the check mark for [Disable
in this hardware profile] in [Device Usage], press [OK], then press [Close].
If uninstalling the touchscreen driver, reinstall the driver following the steps
below.
- [AHL/AR5000 and Digitouch Controllers], delete the check mark for [Disable
in this hardware profile] in [Device Usage], press [OK], then press [Close].
If uninstalling the touchscreen driver, reinstall the driver following the steps
below.
1
In [Start] - [Run], input [c:\util\drivers\tscreen\t5setup.exe], then press [OK].
Simply follow the on-screen instructions. (Select the default value.) If the
computer asks you to reboot the computer, press [Yes].
Simply follow the on-screen instructions. (Select the default value.) If the
computer asks you to reboot the computer, press [Yes].
2
When the Calibration screen is displayed*, point the cursor.
*It is displayed first time only after the computer was rebooted.
*It is displayed first time only after the computer was rebooted.
2
Restart the computer.
3
When the message [Press <F2> to enter SETUP] is displayed, press
and then run the Setup Utility.
and then run the Setup Utility.
4
Select [Advanced] menu and set [Serial Port B] to [Enable] and [Device] to
[Touchscreen].
Press F10 . At the confirmation message, select [Yes] and press Enter .
The computer will reboot.
[Touchscreen].
Press F10 . At the confirmation message, select [Yes] and press Enter .
The computer will reboot.
F2
NOTE
CAUTION
F2