Panasonic cs-pc12dkd cu-pc12dkd cs-pa12dkd cu-pa12dkd g Service Manual
SELECT THE BEST LOCATION
INDOOR UNIT
There should not be any heat source or steam near the
unit.
unit.
There should not be any obstacles blocking the air
circulation.
circulation.
A place where air circulation in the room is good.
ıA place where drainage can be easily done.
ıA
place
where
noise
prevention
is
taken
into
consideration.
ıDo not install the unit near the door way.
ıEnsure the spaces indicated by arrows from the wall,
ceiling, fence or other obstacles.
ıRecommended installation height for indoor unit shall be
at least 2.5 m.
OUTDOOR UNIT
ıIf an awning is built over the unit to prevent direct
sunlight or rain, be careful that heat radiation from the
condenser is not obstructed.
condenser is not obstructed.
There should not be any animal or plant which could be
affected by hot air discharged.
affected by hot air discharged.
Keep the spaces indicated by arrows from wall, ceiling,
fence or other obstacles.
fence or other obstacles.
Do not place any obstacles which may cause a short
circuit of the discharged air.
circuit of the discharged air.
If piping length is over the common length, additional
refrigerant should be added as shown in the table.
refrigerant should be added as shown in the table.
Indoor /Outdo or Unit Installa tion Diagra m
ıı ı
Attach ed access ories
33
CS-PC12DKD/ CU-PC12DKD / CS-PA12DKD / CU-PA12DKD
Attached accessories.
1
No.
Accessories part
Qty. No.
Accessories part
Qty.
1
2
3
4
Installation plate
Installation plate fixing
screw
screw
Remote control
Battery
1
5
1
2
5
Drain elbow
1
6
Connecting Wire (Connector)
*
hr
DEL
A
Y
O
FF
O
N
A
UT
O
AU
T
O
FA
N
SP
EE
D
A
IR
SW
IN
G
MO
D
E
TE
M
P
O
FF
/O
N
TI
M
E
R
O
N
SE
T
A
IR
S
W
IN
G
O
FF
C
A
N
C
E
L
FA
N
S
P
EE
D
A
UTO
C
O
O
L
DRY
FA
N
O
FF
ST
D
Model
PC12DK
PA12DKD
Piping size
Max. Piping
Length
(m)
7
7
Max.
Elevation
(m)
5
5
Additional
Refrigerant
(g/m)
-
-
Gas
1/2"
1/2"
Liquid
1/4"
1/4"
Indoor/Outdoor Unit Installation Diagram
About 1.1 m
Piping direction
Attention not to
bend up drain hose
bend up drain hose
Length of power supply cord
Right
Right Bottom
Right Rear
Left
Rear
Left Bottom
Left
(Front side)
About 1.8 m
<
<
<
<
(Left and right are identical)
This illustration is for explanation purposes only.
The indoor unit will actually face a different way.
The indoor unit will actually face a different way.
Installation plate
1
Sleeve ( )
Bushing Sleeve ( )
Putty (Gum type sealer) ( )
Vinyl tape (Wide) ( )
Apply after carrying out a
drainage test.
To carry out the drainage
test, remove the air filters
and pour water into the heat
exchanger.
To carry out the drainage
test, remove the air filters
and pour water into the heat
exchanger.
Saddle ( )
Additional drain hose ( )
Bend the pipe as closely on
the wall as possible, but be
careful that it doesn't break.
the wall as possible, but be
careful that it doesn't break.
Installation parts you
should purchase ( )
should purchase ( )
1/4" Liquid side piping ( )
10
cm
or
mor
e
Gas side piping ( ) 1/2"
100
cm
or mo
re
30
cm
or mo
re
5c
m
or
more
Insulation of piping connections
Carry out insulation
after checking for
gas leaks and
secure with vinyl
tape.
after checking for
gas leaks and
secure with vinyl
tape.
Vinyl tape
Type designation 245 IEC 57
or heavier cord
or heavier cord
Connecting cable
( )-
(3-CORE WIRE/1.5mm
2
)
5 cm
or more
10 ZZ
or more
(5-CORE WIRE/1.5mm
2
PC12DKD
( )
PA12DKD
+2X0.5mm )-
2
(Only for PA12DKD)
(Only for PA12DKD)