Panasonic dmr-es20deb User Manual
Y
PB
PR
OPTICAL
COMPONENT
VIDEO OUT
(PROGRESSIVE/
INTERLACE)
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
S VIDEO OUT
S VIDEO
AV4 IN
AV4 IN
OUT
AUDIO
R
R
L
L
VIDEO
AC IN
AV1 (TV)
AV2 (EXT)
RF OUT
RF IN
AC mains socket
AC mains lead
Connect DVD Recorder and TV set to the AC
mains socket.
mains socket.
2
3
1
Connect aerial to the RF IN (Aerial input)
connector of the DVD Recorder.
connector of the DVD Recorder.
Connect the DVD Recorder´s RF OUT (Aerial
output) to the TV set’s Aerial in connector.
output) to the TV set’s Aerial in connector.
Disconnect the power of all units.
Follow the steps for Auto-Setup on page 14.
2
Aerial
RF IN
Aerial input
RF OUT
Aerial output
AC mains lead
RF cable /
Aerial cable
Aerial cable
erial
A
input
RF cable /
Aerial cable
Aerial cable
3
3
TV
1
DVD Recorder
AC IN~
Follow the steps below.
Connecting with RF cable (Aerial cable)
Auto-Setup with RF cable (Aerial cable)
(Automatic tuning)
!
Turn on your television set.
!
With the Standby/on switch turn on the DVD Recorder. Automatic tuning for all available
TV stations begins. Approximate duration is 5 minutes.
TV stations begins. Approximate duration is 5 minutes.
- While Auto-Setup is running the first digit of the DVD Recorder display will flash.
After a while it will stop flashing and the RF output channel number will be displayed.
- Select an unused channel pre-set on your TV and tune it to the RF output channel
number shown on the DVD Recorder display (or until you can clearly see the Auto-Setup
screen). Store the new RF output channel (refer to the instructions for your TV).
screen). Store the new RF output channel (refer to the instructions for your TV).
In some cases, the RF output channel may interfere with the TV stations transmitted in
your area. This may prevent you from seeing the On-Screen Display clearly.
Please see page 15 for removing the interference before restarting Auto-Setup.
your area. This may prevent you from seeing the On-Screen Display clearly.
Please see page 15 for removing the interference before restarting Auto-Setup.
You can complete the Owner ID now or skip this step and do it later. To do it later, press the
RETURN button. Your DVD Recorder is now ready to use.
RETURN button. Your DVD Recorder is now ready to use.
!
To set the Owner ID now, use and press the Numeric buttons or
to enter a four-
digit PIN number. Press , to correct the digit.
!
Make sure that you will remember the PIN number (make a note of it).
!
Press the ENTER button twice to confirm.
!
Enter the [Name], [House No] and [Postcode] in the same way, using
.
!
Press the ENTER button to confirm each entry.
!
Press the RETURN button to leave the Owner ID screen.
!
You will now see the TV picture. Your DVD Recorder is now ready to use.
Owner ID
If the clock setting menu appears
(Auto clock set was not possible due to a weak signal)
(Auto clock set was not possible due to a weak signal)
!
Press
to set the correct time and date and press ENTER to finish this setting.
Note: A wrong date or time will influence the programmed recording of TV programmes
(don't forget to change summer time and winter time).
(don't forget to change summer time and winter time).
DVD Display
Clock
Off
Automatic
0
00
00
1
1
2005
:
:
.
.
Time
Date
CHANGE
ENTER
RETURN
Clock cannot be set automatically.
Please set the clock manually.
ENTER: store RETURN: leave
SELECT
0
9
No
Auto-Setup
Ch
4
Suche Sender, bitte warten.
RETURN: abbrechen
RETURN: abbrechen
35
Auto-Setup in progress, please wait.
RETURN: to abort
RETURN
Owner ID
RETURN
Name
House No.
Postcode
PIN number
* * * *
RETURN : leave
!
After Automatic tuning has finished, the Owner ID screen will appear.
14
43