Panasonic pt-lm1e User Manual
E
NGLISH
-43
Adjustments
and
settings
42-E
NGLISH
Press the F or G button on the
projector or remote control unit to
select an item, then press the I or
H button to change the setting.
projector or remote control unit to
select an item, then press the I or
H button to change the setting.
OSD
ON
The signal name is displayed in the
top-right corner of the screen when
the input signal is changed.
The signal name is displayed in the
top-right corner of the screen when
the input signal is changed.
OFF
Use this setting when you do not
want the signal name to be
displayed.
Use this setting when you do not
want the signal name to be
displayed.
AUTO SIGNAL
This should normally be set to “ON”.
ON
“AUTO SETUP” will be carried out
automatically when the input signal
is changed.
OFF
“AUTO SETUP” will not function
when the input signal is changed.
“AUTO SETUP” will be carried out
automatically when the input signal
is changed.
OFF
“AUTO SETUP” will not function
when the input signal is changed.
AUTO KEYSTN
This should normally be set to “ON”.
ON
During “AUTO SETUP”, the angle of
tilt of the projector is detected and
keystone distortion is corrected
automatically.
During “AUTO SETUP”, the angle of
tilt of the projector is detected and
keystone distortion is corrected
automatically.
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during “AUTO
SETUP”, such as when the screen
itself is at an angle.
Use this setting when you do not
want automatic keystone correction
to be carried out during “AUTO
SETUP”, such as when the screen
itself is at an angle.
RGB/YP
B
P
R
This should normally be set to
“AUTO”. RGB or YP
“AUTO”. RGB or YP
B
P
R
is selected
automatically depending on the
synchronising signal status.
When HDTV, 525p, 525i, 625p,
625i, 750p, and some VGA480
signals are being input, select
“RGB” or “YP
synchronising signal status.
When HDTV, 525p, 525i, 625p,
625i, 750p, and some VGA480
signals are being input, select
“RGB” or “YP
B
P
R
” in accordance
with the input signal.
VGA60/525P
When a VGA60 or 525p RGB signal
is being input, select the signal in
accordance with the input signal.
is being input, select the signal in
accordance with the input signal.
SXGA MODE
This setting is only for an SXGA
signal.
signal.
SXGA
Select this item normally.
Select this item normally.
SXGA+
When the edges of the projected
image are not visible, select this item.
When the edges of the projected
image are not visible, select this item.
Noise Reduction (NR)
(S-VIDEO/VIDEO only)
If noise occurs from the projector
because of a poor input signal, set
“NR” to “ON”.
To turn off the “NR” feature, set it to
“OFF”.
because of a poor input signal, set
“NR” to “ON”.
To turn off the “NR” feature, set it to
“OFF”.
BACK COLOR
This sets the colour which is
projected onto the screen when no
signal is being input to the projector.
projected onto the screen when no
signal is being input to the projector.
FRONT/REAR
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 17.)
accordance with the projector
setting-up method. (Refer to page 17.)
FRONT
When the projector is placed in front
of a screen.
When the projector is placed in front
of a screen.
REAR
When using a translucent screen.
When using a translucent screen.
DESK/CEILING
This setting should be changed in
accordance with the projector
setting-up method. (Refer to page 17.)
accordance with the projector
setting-up method. (Refer to page 17.)
DESK
When the projector is placed on a
desk or similar.
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
Set “FAN CONTROL” to “HIGH”,
when using this projector at high
elevations (above 1 400 m) only.
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced. This can help to extend
the lamp’s operating life. If using the
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced. This can help to extend
the lamp’s operating life. If using the
R G B / Y P
B
P
R
A U T O
[
R G B
[
Y P
B
P
R
V G A 6 0 / 5 2 5 P 5 2 5 P
[
V G A 6 0
B A C K C O L O R B L U E
[
B L A C K
F R O N T / R E A R F R O N T
[
R E A R
D E S K / C E I L I N G D E S K
[
C E I L I N G
L A M P P O W E R H I G H
[
L O W
S X G A M O D E S X G A
[
S X G A +
F A N C O N T R O L S T A N D A R D
[
H I G H
Option settings
O P T I O N 1
O S D O N
A U T O S I G N A L O N
A U T O K E Y S T N O N
R G B / Y P
B
P
R
A U T O
V G A 6 0 / 5 2 5 P V G A 6 0
S X G A M O D E S X G A
N R O F F
S E L E C T A D J R E T R N
O P T I O N 2
B A C K C O L O R B L U E
F R O N T / R E A R F R O N T
D E S K / C E I L I N G D E S K
F A N C O N T R O L S T A N D A R D
L A M P P O W E R H I G H
L A M P R U N T I M E 1 0 0 H
F U N C 1 I N D E X
C O N T R O L K E Y O N
A U T O P O W . O F F D I S A B L E
P O W E R M E M O R Y O N
S E L E C T A D J R E T R N
NOTE:
B The setting for “TV-SYSTEM”
B The setting for “TV-SYSTEM”
will also be displayed when an
S-VIDEO/VIDEO signal is being
input.
S-VIDEO/VIDEO signal is being
input.
N R O F F
[
O N