Panasonic sa-ht833v User Manual
40
RQT7921
The radio
Press [TUNER] to put the remote control in TUNER mode.
Up to 15 stations can each be set in the FM and AM bands.
1
Press [FM/AM] to select “FM”.
2
Press [
6] or [5] to tune to the
lowest frequency (“FM 87.9” MHz or
“FM 87.5” MHz).
“FM 87.5” MHz).
3
Press and hold [ENTER].
Release the button when “AUTO” is displayed.
The tuner presets all the stations it can receive into the channels
in ascending order.
≥“SET OK” is displayed when the stations are set. The last
in ascending order.
≥“SET OK” is displayed when the stations are set. The last
station to be set is then played.
≥“ERROR” is displayed when automatic presetting is
unsuccessful. Preset the channels manually (
l right).
4
Repeat steps 1 to 3 to set the AM bands
(the lowest frequency is “AM 520” kHz).
(the lowest frequency is “AM 520” kHz).
1
Press [FM/AM] to select “FM” or “AM”.
2
Press [
6] or [5] to select the
frequency.
Press and hold [
6] or [5] until the frequency starts scrolling
to start automatic tuning. Tuning stops when a station is found.
1
Tune to the station (
l above).
2
Press [ENTER].
3
While “PGM” is blinking on the display
Press the numbered buttons to select a
channel.
channel.
Alternatively, press [
W CH] or [X CH] then press [ENTER].
The station occupying a channel is erased if another station is preset
to that channel.
to that channel.
1
Press [FM/AM] to select “FM” or “AM”.
2
Press the numbered buttons to select
the channel.
the channel.
Alternatively, press [
W CH] or [X CH].
To select a 2-digit number
e.g. 12: [
e.g. 12: [
S10]
l [1] l [2].
When a stereo FM broadcast is being received.
∫ If noise is excessive in FM
Press [PLAY MODE] to display “MONO”.
Press [PLAY MODE] again to cancel the
mode.
The mode is also canceled when you change
the frequency.
mode.
The mode is also canceled when you change
the frequency.
∫ FM frequency step
Main unit only
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated in 0.1 MHz steps.
1 Press [INPUT SELECTOR]
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated in 0.1 MHz steps.
1 Press [INPUT SELECTOR]
on the main unit to select “FM”.
2 Press and hold [INPUT SELECTOR].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
Automatic presetting
Manual tuning
OPEN/CLOSE
EJECT
DISC CHECK
/REW
FF/
STOP
PLAY
DOWN
UP
PHONES
VOLUME
STOP
-DEMO
PLAY
H.BASS
REC
CH
INPUT SELECTOR
VOLUME
1
2
3
4
5
6
7
8
0
DISC
9
CH
NAVI
CANCEL
SPEED
PROG
SKIP
SLOW/SEARCH
MENU
ENTER
DIRECT
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TV
FM/AM
DVD/VHS
DVD
TV
VHS
TUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECT
JET REW
ENTER
PLAY
LIST
TV VOL
TV VOL
MULTI RE-MASTER
QUICK OSD
MIX 2CH
ZOOM
PROGRESSIVE
CD MODE
REPEAT
PLAY MODE
H.BASS
SUBWOOFER LEVEL
C.FOCUS
SFC
TEST
SUPER SRND
CH SELECT
MUTING
CM SKIP
ADVANCE
DISC REVIEW
QUICK
REPLAY
REC
SLEEP
PL
AUDIO
RESET
TV/VIDEO
SHIFT
SHIFT
INPUT SELECTOR
ENTER
PLAY MODE
FM/AM
TUNER
Numbered
buttons
buttons
CH
CH
CH
SHIFT
C. FOCUS
SFC
TEST
SUPER SRND
SUPER SRND
PL
S10
H.BASS
CH SELECT
VOLUME
∫ Presetting the channel one by one
Selecting the preset channels
PGM
ST
TUNED
MONO
[Remember]
Press [TUNER] first.
RQT7921-P_ENG.book 40 ページ ２００５年５月２５日 水曜日 午後３時２４分