Panasonic sb-tp20gn User Manual
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/
Web Site : http://www.panasonic.co.jp/global/
RQT6901-B
M1202TK0
En
Notes
Speaker impedance and allowed input
SB-FS702 / SB-PC702
Impedance
6
Ω
Input power
100 W (DIN)
SB-FS802 / SB-PC802
Impedance
6
Ω
Input power
40 W (DIN)
The only receivers or amplifiers you should connect to these speak-
ers are those whose rated output does not exceed the above figures.
Using a receiver or amplifier with higher ratings than listed above can
cause abnormal sounds to occur because of excessive input, dam-
age to the receiver or speakers, and fire. If equipment is damaged in
any way or unexpected trouble occurs during playback, unplug the
system from its outlet and call a serviceman for help.
ers are those whose rated output does not exceed the above figures.
Using a receiver or amplifier with higher ratings than listed above can
cause abnormal sounds to occur because of excessive input, dam-
age to the receiver or speakers, and fire. If equipment is damaged in
any way or unexpected trouble occurs during playback, unplug the
system from its outlet and call a serviceman for help.
Protection circuitry
SB-FS702 / SB-PC702 / SB-FS802 / SB-PC802
These units incorporate protection circuitry to protect them from dam-
age caused by excessive input or abnormal signals; when excess
input is detected, input is automatically interrupted.
These units incorporate protection circuitry to protect them from dam-
age caused by excessive input or abnormal signals; when excess
input is detected, input is automatically interrupted.
If sound is interrupted...
1.Reduce the volume of the receiver (or amplifier).
2.Check the sound source and connections for any problems.
2.Check the sound source and connections for any problems.
If there is no problem, the protection circuitry will reset in a few
minutes.
minutes.
After the protection circuit is reset...
Take care not to increase the receiver’s volume too high.
Excessive input
You can damage your speakers and shorten their useful
life if you play sound at high levels over extended periods.
life if you play sound at high levels over extended periods.
Reduce the volume in the following cases to avoid damage :
•When playing distorted sound.
•When the speakers are receiving howling from a microphone or
record player, noise from FM broadcasts, or continuous signals from
an oscillator, test disc, or electronic instrument.
an oscillator, test disc, or electronic instrument.
•When adjusting the sound quality.
•When turning the amplifier on or off.
Other notes
If irregular coloring occurs on your television :
These speakers are designed to be used close to a television, but the
picture may be affected with some televisions and set-up combina-
tions.
If this occurs, turn the television off for about 30 minutes.
The television’s demagnetizing function should correct the problem.
If it persists, move the speakers further away from the television.
picture may be affected with some televisions and set-up combina-
tions.
If this occurs, turn the television off for about 30 minutes.
The television’s demagnetizing function should correct the problem.
If it persists, move the speakers further away from the television.
You cannot remove the speaker net.
Keep magnetized items away.
Magnetized cards, bank cards, commuter passes, etc., can be dam-
aged if allowed too near speaker magnets. Clocks may also be af-
fected.
aged if allowed too near speaker magnets. Clocks may also be af-
fected.
Avoid locations such as described below :
•In direct sunlight
•Near heating appliances or other sources of heat
•Near heating appliances or other sources of heat
•Where the humidity is high
Maintenance
Clean these units with a soft, clean, dry cloth.
Clean regularly to maintain the polished surface.
•Never use alcohol, paint thinner, or benzine to clean these units.
•Before using chemically treated cloth, read the instructions that came
•Never use alcohol, paint thinner, or benzine to clean these units.
•Before using chemically treated cloth, read the instructions that came
with the cloth carefully.
Specifications
SB-FS702 / SB-PC702
Type
2 way 2 speaker system Bass-reflex type
Speaker (s)
Woofer:
6.5 cm cone type x 1
Fullrange:
6.5 cm cone type x 1
Impedance
6
Ω
Input power
200 W (Music), 100 W (DIN)
Sound pressure level
82 dB/W (1.0 m)
Crossover frequency
7 kHz
Frequency range
100 Hz – 25 kHz (at –16 dB)
125 Hz – 22 kHz (at –10 dB)
125 Hz – 22 kHz (at –10 dB)
Dimensions (W x H x D)
SB-FS702
135 x 295 x 145 mm (with the stand)
SB-PC702
250 x 140 x 145 mm (with the stand)
Mass
1.55 kg
SB-FS802 / SB-PC802
Type
1 way 1 speaker system Bass-reflex type
Speaker (s)
Fullrange:
6.5 cm cone type x 1
Impedance
6
Ω
Input power
80 W (Music), 40 W (DIN)
Sound pressure level
79 dB/W (1.0 m)
Frequency range
110 Hz – 25 kHz (at –16 dB)
130 Hz – 22 kHz (at –10 dB)
Dimensions (W x H x D)
SB-FS802
110 x 226 x 132 mm (with the stand)
SB-PC802
180 x 139 x 132 mm (with the stand)
Mass
0.93 kg
SB-WA55 / SB-WA54
SPEAKER SECTION
Type
1 way 1 speaker system Bass-reflex type
Speaker (s)
Woofer:
17 cm cone type x 1
Impedance
6
Ω
Input power
200 W (Music), 100 W (DIN)
Sound pressure level
80 dB/W (1.0 m)
Frequency range (with amp)
32 – 300 Hz (at –16 dB)
38 – 240 Hz (at –10 dB)
38 – 240 Hz (at –10 dB)
AMPLIFIER SECTION
Output power
100 W (6
Ω) (THD 0.9%)
Input sensitivity / Input Impedance
300 mV/33 k
Ω (RCA jack)
Phase switching SB-WA55
NORMAL/REVERSE
Low pass filter
SB-WA55
50 – 200 Hz Variable
SB-WA54
200 Hz Fixed
GENERAL
Power supply
For the United Kingdom, Australia and New Zealand
AC 230 – 240 V, 50 Hz
For others
AC 220 – 240 V, 50/60 Hz
Power consumption
168 W
Dimensions (W x H x D)
SB-WA54 / SB-WA55 For Australia and New Zealand
162 x 457 x 420 mm
SB-WA55 For others
162 x 457 x 434 mm
Mass
SB-WA55
10.8 kg
SB-WA54
10.6 kg
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Mass and dimensions are approximate.