Panasonic sx-pr54m User Manual
Part V
Disk Drive
93
QQTG0701
Dis
k
Driv
e
Loading data
Recall (load) the data from the disk to this instrument’s memories.
•
Note that the load procedure causes any data which is currently stored in the relevant memories to be erased.
LOAD
Load data that saved to a disk into this instru-
ment’s memory.
ment’s memory.
1.
Insert the disk with the stored data into the
Disk Drive. Push it all the way in until you hear
a click.
Disk Drive. Push it all the way in until you hear
a click.
2.
On the DISK MENU display, select LOAD.
• The display looks similar to the following.
• If there are only SMF files on the disk, the display auto-
matically changes to the SMF LOAD display.
3.
Use the buttons below the display to select the
song (Technics file) you wish to load.
song (Technics file) you wish to load.
• If there are SMF files on the disk and you wish to load an
SMF file, press the SMF button. (Refer to next page.)
4.
Press the LOAD button.
• The LOAD operation begins.
• When the operation has been successfully completed,
• When the operation has been successfully completed,
“COMPLETED!” is shown on the display.
• If song data was loaded, you can press the
START/STOP button to begin playback when the
SEQUENCER PLAY display is active.
SEQUENCER PLAY display is active.
• You can load the type of data for which only one song
can be recorded in the SEQUENCER. (This type is avail-
able for disks used with older Technics models.) Note,
however, that in this case, the song is loaded into SONG
1, but the data in SONG memories 2 to 10 are erased.
able for disks used with older Technics models.) Note,
however, that in this case, the song is loaded into SONG
1, but the data in SONG memories 2 to 10 are erased.
• You can also access the LOAD display by pressing the
DISK button for a few seconds.
䡲䡲䡲䡲
LOAD OPTION
Specify the kind of data you wish to load from the
disk to your instrument.
disk to your instrument.
1.
Use the PAGE buttons to access the PAGE
2/3 LOAD OPTION display.
2/3 LOAD OPTION display.
• The display looks similar to the following.
2.
Use the buttons below the display to specify
the types of data you wish to load (YES/NO).
the types of data you wish to load (YES/NO).
• - - - - - indicates that this type of data has not been saved.
• This setting is canceled when you quit the LOAD display
• This setting is canceled when you quit the LOAD display
or when another file is selected.
3.
Press the LOAD button.
• The LOAD operation begins.
䡲䡲䡲䡲
SINGLE LOAD
You can specify which data to load from a disk
into a specific PANEL MEMORY, COMPOSER
(MEMORY),
into a specific PANEL MEMORY, COMPOSER
(MEMORY),
SOUND MEMORY,
EFFECT
MEMORY or SEQUENCER (when SONG SAVE
was executed) memory.
was executed) memory.
1.
Use the PAGE buttons to access the PAGE
3/3 SINGLE LOAD display.
3/3 SINGLE LOAD display.
• The display looks similar to the following.
2.
Use the MODE button to select the data you
wish to load.
wish to load.
3.
Use the BANK/SINGLE button to select the
load increment. (except for SEQUENCER)
load increment. (except for SEQUENCER)
BANK:
Load one bank at a time.
SINGLE:
Load the smallest data increment.
4.
Follow the appropriate procedure to load the
specified data.
specified data.
• Specify the data source for SONG (left side), and the
data destination (this instrument’s memory location) for
TO.
TO.
10_Part V.fm 93 ページ ２００３年５月１６日 金曜日 午後８時４１分