Panasonic th-65pf11uk User Manual

Locks the input switch operation.

Notes:
• Only the adjusted signal is displayed (see page 15).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input in 

the single screen display mode.

• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal. 

(Ex. INPUT1A, INPUT1B) 

On 

Off:  All the buttons on main unit can be used.
MENU&ENTER: Locks 

MENU

 and 

ENTER/

 buttons on main unit.

On:   Locks all the button on main unit.

Sets Button lock with the unit buttons in the following procedure.
Off:   Press   four times→Press 

INPUT

 four times→Press   four times→Press 

ENTER/

MENU&ENTER: Press 

ENTER/

 four times→Press   four times→Press 

INPUT

 four times→Press 

ENTER/

On:   Press   four times→Press 

ENTER/

 four times→Press   four times→Press 

ENTER/

Off:  You can use all of the buttons on the remote control.
User1: You can only use 

, 

, 

, 

,  , 

, 

, 

 buttons on the remote control.

User2: You can only use  

, 

 buttons on the remote control.

User3: Locks all the buttons on remote control.

Enable:  Enables the “Off-timer function”.

Disable:  Disables the “Off-timer function”.

Note:   

When “Disable” is set, the Off-timer is cancelled.

Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.

Normal:  Power returns in as the same state as before the power interruption.

Standby:  Power returns in standby mode. (Power Indicator : red/orange)

On: 

 

Power returns in power On. (Power Indicator : green)

Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.

Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.

Set value range: 0 - 100

(Standard value: 0)

Off:  Disables ID remote control functions. You can use normal remote control operations.

On: 

Enable ID remote control functions.

Note:  To use the ID remote control function, it is necessary to set each ID number of remote control and 

display unit. About the setting method, please refer to “ID Remote Control Function” (see page 35) 

and “ID select” (above-mentioned).

Sets the panel ID Control.

Off:  Disables external control by the ID.

On: 

Enables the external control by the ID.

Adjusts the image display size on screen.

Off:  Sets the normal image display size on screen.

On: 

Sets the image display size approximately 95 % of the normal image display.

Notes:
• This setting is valid only when the input signals are as follows; 
  NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD)) 

525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 
1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)

• This setting is invalid when two screen display, digital zoom, Multi display or Portrait display is selected.
• When “Display size” is set to “On”, “H-POS” and “V-POS” in “POS. /SIZE” can be adjusted.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.