Alpine CDA-9886R User Manual
16
-EN
Adjusting Subwoofer Level/Bass Level/
Treble Level/Balance (Between Left and
Right)/Fader (Between Front and Rear)/
Auto Volume/Defeat
Treble Level/Balance (Between Left and
Right)/Fader (Between Front and Rear)/
Auto Volume/Defeat
1
Press Rotary encoder (AUDIO) repeatedly to
choose the desired mode.
choose the desired mode.
Each press changes the mode as follows:
SUBWOOFER*
1
BASS
TREBLE
BALANCE
FADER
AUTO VOLUME*
2
DEFEAT
VOLUME
SUBWOOFER
Subwoofer level: 0 ~ +15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER, AUTO
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
*
1
When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to “Turning Subwoofer ON/OFF” (page 18).
refer to “Turning Subwoofer ON/OFF” (page 18).
*
2
By setting AUTO VOLUME, the unit can automatically adjust
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
obtained in each mode.
By setting Defeat ON, previously adjusted settings of BASS
and TREBLE will return to the factory defaults.
and TREBLE will return to the factory defaults.
• Depending on the connected devices, some functions and display
indications do not work.
Setting the Subwoofer Level
You can change the Subwoofer Level to create your own tonal
preference.
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
mode.
2
Turn the Rotary encoder to select the SUBW. Level
Adjustment mode, and then press
/ENT.
SUBW. Level*
3
Bass*
4
Treble*
4
HPF*
4
Black Out
SUBW. Level
3
Turn the Rotary encoder to select the desired
subwoofer level (0~+15).
subwoofer level (0~+15).
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
*
3
When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to “Turning Subwoofer ON/OFF” (page 18).
refer to “Turning Subwoofer ON/OFF” (page 18).
The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer to “Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Auto Volume/Defeat” (page 16).
(AUDIO). Refer to “Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Auto Volume/Defeat” (page 16).
*
4
The function is inoperable when DEFEAT is set to ON.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
mode.
2
Turn the Rotary encoder to select the Bass
Adjustment mode, and then press
Adjustment mode, and then press
/ENT.
SUBW. Level*
5
Bass*
6
Treble*
6
HPF*
6
Black Out
SUBW. Level
3
-1 Press BAND/TA to select the desired bass centre
frequency.
80 Hz
100 Hz
200 Hz
60 Hz
80 Hz
Emphasises the displayed bass frequency ranges.
3
-2 Press SOURCE/
to select the desired bass
bandwidth.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
wider setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
Sound Setting
/ENT
BAND/TA
Rotary encoder (AUDIO·LOUD)
SOURCE/
SOUND SETUP
/ESC
Setting the Bass Centre Frequency
Setting the Bass Bandwidth
Q1
Q2
Q3
Q4