Panasonic ty-la1000k User Manual
WARNING:
The lamp may be hot. Be careful when handling.
The lamp may be hot. Be careful when handling.
CAUTION:
• High-pressure lamp may explode if improperly
• High-pressure lamp may explode if improperly
handled.
• Danger of injury due to glass fragments.
■ Lamp replacement procedure
1
Turn power off, wait until power
indicator stops blinking red, then
unplug the power cord from the wall
outlet and confi rm that the area around
the lamp unit has cooled down.
• Please wait more than one hour for lamp
replacement.
[If you need to replace the lamp more urgently]
• The Projection display has a forced cooling
• The Projection display has a forced cooling
feature. After the POWER button is turned OFF,
and during the fi rst minute of the normal cooling
fan operation, press the VOL+ button on the
projection display and ▲ button on the remote
control at same time for more than 5 seconds. The
cooling fan operates for about 10 minutes. The
LAMP indicator fl ashes red 5 times every 5
seconds.
and during the fi rst minute of the normal cooling
fan operation, press the VOL+ button on the
projection display and ▲ button on the remote
control at same time for more than 5 seconds. The
cooling fan operates for about 10 minutes. The
LAMP indicator fl ashes red 5 times every 5
seconds.
POWER
button
/POWER
indicator
button
/POWER
indicator
Lamp Replacement
3
Loosen the Lamp cover screw.
First read caution and warning labels
on lamp cover. Then, loosen the lamp
cover screw by using a screwdriver.
Lamp unit screw
Screwdriver
4
Loosen the lamp unit screw with a
screwdriver. Then, grasp the lamp unit
as shown in the diagram, and slowly
remove from the projection display.
• Do not drop, as the impact of dropping may cause
the lamp to explode.
2
Remove the Front cover. Place your
fi ngertips under the Front cover and
pull it from the projection display.
Lamp unit handle
Lamp cover handle
6
Replace the Lamp unit and cover
screws. Tighten the lamp unit/cover
screw with a screwdriver.
• Properly dispose of old lamp.
Attach the lamp unit and lamp unit housing door
securely. If the lamp unit and lamp unit housing
door are not attached securely, the protective
circuit will be activated and the lamp will not turn
on.
securely. If the lamp unit and lamp unit housing
door are not attached securely, the protective
circuit will be activated and the lamp will not turn
on.
Note
7
Replace the Front cover.
5
Insert the new lamp unit being careful
of the insertion direction.
• Press on the arrow mark making sure insertion is
done correctly.
■ Lamp time reset procedure
1
Be sure the power cord is plugged into
a properly grounded wall outlet. Then,
press the POWER button on the projection
display or the remote control to turn the
unit on.
Warning:
Perform lamp time reset only when the lamp has
been replaced.
Perform lamp time reset only when the lamp has
been replaced.
When lamp time reset is fi nished, the LAMP
indicator goes out.
indicator goes out.
Note
After lamp replacement,
follow the procedure below
follow the procedure below
3
When reset
procedure is
complete, the
screen on the right
will appear.
and
Lamp cover screw
LAMP indicator
2
While pressing the VOL- button on
the projection display, hold down the
PIP button on the remote control at
same time for more than 5 seconds.
LSQC0335
CAUTION:
[Under no circumstance should you touch the
actual bulb.]
At this high operating temperature the natural oil
on your fi nger can cause the glass to weaken
where touched and the bulb can crack or explode.
[Under no circumstance should you touch the
actual bulb.]
At this high operating temperature the natural oil
on your fi nger can cause the glass to weaken
where touched and the bulb can crack or explode.
CAUTION:
Because of the possibility of injury, strictly follow the
replacement procedure below.
Because of the possibility of injury, strictly follow the
replacement procedure below.
LAMP TIME WAS
RESET TO 0.
EXIT
Front cover