Panasonic ty-s42px20u User Manual

TQZH507      Printed in Japan

 1. 

Align the support pole insertion holes of the plasma 

TV with the support poles 

 

 (1 each), and

lower the plasma 

TV until the poles stop. Slightly lift the left and right sides of the plasma 

TV and

remove the corner protection pads attached to the bottom.

2. Fasten the plasma 

TV and support poles 

 

 using as

sembly screws (black screws)  

 (

× 

4)

   

T

op crosspiece

   Bottom panel

   Side panel (Left)

   Side panel (Right)

   Rear cord cover

   Glass shelf

   Cord holder

   

TBLA01

17

   

TBLH0550

   

TBLA0104

   

TBLA0103

   

TBLB31

10

   

TKGA0129

   

TBLA3217

  1   

TBLA01

16

  1   

TBLH0548

  1   

TBLA0104

  1   

TBLA0103

  1   

TBLB3080

  1   

TKGA0127

  1   

TBLA3184

Painted Surfaces:Use a damp cloth for cleaning. Do not use any abrasive or chemically treated cleaners.

NOTE: 

As with all indoor furniture, this unit should not be exposed to direct sunlight, extreme temperatures

or moisture, as this can result in serious irreparable damage.

Placement

 T

o

 thread wiring, remove the terminal cover and pass wires along the

grooves in the rear cord cover

, along the groves in the left and right

side panels, and along the groves in the cord holder under the glass

shelf.

∗

 Some equipment may have short cords. In such an instance, thread

the wiring over the minimum distance, as indicated by the dotted line in

the diagram.

 After threading wiring, fasten with cord clamps 

 (

×

 6) so that the cords

do not protrude from the grooves. Finally

, attach the terminal cover

.

   If there are any cord clamps 

 left over

, store them carefully

. 

Y

ou will

need them if you use the unit to house more equipment in the future.

A study of the assembly instructions will not only save you time, but may prevent possible damage to your

new stand.

Assistance may be required for some assembly procedures.

 THIS ST

AND IS DESIGNED ONL

Y

 FOR USE WITH 

A

 P

ANASONIC PLASMA

 TV

.

TH-42PX20, TH-50PX20

Use with other appliances may result in instability causing possible injury

.

Assembly screws

Glass shelf fastening screws

Glass shelf support fastening

screws (Black screws)    ( 

× 

4)

Rear cord cover fastening

screws (Black screws)    ( 

× 

3)

Assembly screws (Black screws)

Support pole (Right)

Support pole (Left)

Cord clamps

THEA1

18 

× 

4

THEA102N 

× 

8

XSB4+12FZ 

× 

7

XST5+12 

× 

4

XYN5+F55FZ 

× 

4

TBLA3194 

× 

2

TBLA3197 

× 

1

TBLB31

1

1

 

× 

6

Bottom cap (Right)

TBLB3107 

× 

1

Bottom cap (Left)

TBLB3108 

× 

1

Screws

XTB4+10B 

× 

4

TBLA3196 

× 

1

Support pole fastening screws

Glass shelf supports (Right)

Glass shelf supports (Left)

Casters (Wheels)

TBLA3195 

× 

2

TBLB3074 

× 

4

∗

 Wire over the minimum distance

Cord clamps 

Power cord

(Back)

∗

 The top glass shelf is specifically for the center speaker and 

A

V

amp. If you place a video deck here, it may badly af

fect the picture.

     20421 84th 

A

venue South, Kent, W

ashington 98032                 

T

el. : 1-800-833-9626                 Fax : 1-800-237-9080

2003 Matsushita Electric Industrial Co., Ltd. 

All rights reserved. Unauthorized copying and distribution is a violation of law

.

     5770 

Ambler Drive, Mississauga, Ontario L4W 2T3                  

T

el. : (905) 624-8447

2003 Matsushita Electric Industeial Co., Ltd. 

All rights reserved. Unauthorized copying and distribution is a violation of law

.

 

∗

 Install the plasma 

TV by referring to the following illustration.

 

∗

 Do not hold the plasma 

TV at the bottom of the front panel.

Lift and

remove

Support pole

(Left) 

Assembly screws

(Black screws) 

Corner

protection pad

Support pole (Right) 

Support pole

insertion hole

∗

 Position by placing your hands at the

points indicated in the illustration.

The tools required:

Plus (Phillips) (+) screwdriver