Panasonic ty-wk42pv3u User Manual

Before commencing work, carefully read these Instructions and the Manual for the wide plasma display to ensure

that fitting is performed correctly

.

(Please save these instructions. Y

ou may need them when maintaining or moving the bracket.)

• Fit so that the arrow marks on the wall hanging bracket point upward.

• 

If the wall consists of a material such as concrete and bolts or nuts must be

embedded beforehand, determine the hole positions by aligning using the actual

wall hanging bracket, or calculate hole positions based on the dimension drawing,

and then embed "M6" bolts or nuts. When embedding bolts, locate so that the bolts

protrude from the wall by 10 to 15 mm (25/64 to 19/32 inches).

(1) Fasten the screw at the top center hole first.

(2) 

Using a level, correct any bracket inclination, and then fasten screws at the

remaining 5 locations.

(1) 

Locate the insulation spacers on the top of the plasma TV

unit into the notch on the top of the wall hanging bracket,

and slide down.

(2) 

Lift the plasma TV unit a little, insert the bottom insulation

spacers into the holes on the bottom of the wall hanging

bracket, and slide the unit down.

(3) 

Attach securely using the included unit fastening screws

(1 each for left and right).

• 

There are 22 holes in the wall hanging bracket.

If the wall material is wood, and adequate

attachment strength cannot be ensured by

fastening at the 6 points at right, use as many

spare holes as necessary. However, exercise

care because some wall materials may crack if

screws are located too close together. 

The following dimensions are important. Do not

fit at any location where these dimensions

cannot be secured.

TQZH498

• Use commercially available M6 screws suited to the wall surface material

(wood, steel frame, concrete etc.) for fitting the bracket to the wall.

320 (12 19/32)

11

(7/16)

415 (16 11/32)

370 (14 9/16)

775 (30 33/64)

735 (28 15/16)

660 (25 63/64)

23 (29/32)

AB

C

TH-37PA20

TH-42PA20

TH-42PX20

TH-50PX20

Model name

1070 (42  1/ 8)

1170 (46  1/16)

1140 (44 57/64)

1329 (52 21/64)

596 (23 15/32)

656 (25 53/64)

757 (29 51/64)

870 (34   1/ 4)

120 (4  47/64)

150 (5  29/32)

237 (9  21/64)

294 (11 37/64)

Allen head countersunk screw

Dished toothed washer

Insulation spacer

Allen wrench

• Be sure to securely tighten the fastening

screws to keep the plasma TV from becoming

loose.

• Do not hold any PX20 Series plasma TV by the

bottom of the front panel.

(1) 

Remove the red screws for open/close fastening (one each

on the left and right) 

.

(2) 

Raise the plasma TV towards yourself, as shown in the

diagram at right, push up the lock bracket in the arrow

direction (upward), check that the bracket has locked, and

tentatively fasten. Securely fasten the red screw for

open/close fastening (one screw on left side) 

to the lock

bracket fastening hole 

.

(3) 

After the above preparation, wire to equipment.

(1) 

Remove the screws for unit fastening (1 each on the left

and right) that are fitted to the wall hanging bracket sides.

(2) 

While lifting the bottom of the plasma TV unit, pull it

towards yourself.

(3) 

When the lower insulation spacers are freed, keep lifting

upward.

• Be sure to always fit the red screws for

open/close fastening 

in order to fasten the

plasma TV.

Dimensions of clearance required 

around wall hanging bracket  Unit: mm (inches)

(1) 

After wiring, remove the red screw for open/close

fastening on the left side, raise the unit towards yourself

once, and then slowly lower it again. The lock will release.

(2) 

Securely fasten the red screws for open/close fastening

(one each on the left and right) 

to the fitting holes on

the side of the unit.

Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the procedure 

below.

(1) 

Remove the terminal cover on the plasma TV (PX20 series only).

(2) 

Using a flathead screwdriver, remove the four caps

from the plasma TV.

* 

Carefully retain the removed terminal cover and

caps in a safe place. (They will be needed again

later should it be required to use the special-

purpose stand or standalone stand.)

(3) 

Using the included Allen wrench, fit the included

Allen head countersunk screws, dished tooth

washers and insulation spacers (4 sets) into the

holes from where the caps were removed. (See

the diagram at right.)

Web Site : http://www.panasonic.co.jp/global/

C

Matsushita Electric Industrial Co., Ltd.

2003