Panasonic wj-hd220 User Manual
10
SIGNAL GND
POWER
DATA
10/100BASE-T
MODE
RS-232C
MULTI
SCREEN OUT
SPOT
OUT
1
1
ALARM/REMOTE
OFF
ON
2
2
3
3
4
4
5
5
6
6
7
7
8
8
OUT
VIDEO
OUT
AUDIO
IN
IN
#1
#3
#0
#2
#4
#6
#9 $0
#5
#7
#8
$1
$2 $3
$4
■ Rear View
#0 Audio Input Connector (AUDIO IN)
An RCA standard jack that accepts an unbalanced
–10 dBV, 10 k
–10 dBV, 10 k
Ω line input audio signal supplied from an
external device.
#1 Audio Output Connector (AUDIO OUT)
An RCA standard jack that supplies an unbalanced
–10 dBV, 600
–10 dBV, 600
Ω line output audio signal to an external
device.
#2 Video Input Connector (VIDEO IN 1-8)
Connectors 1-4 allow direct connection of the PSD
cameras (video and commands multiplexed) while con-
nectors 5-8 accept only normal video signals. A 75
cameras (video and commands multiplexed) while con-
nectors 5-8 accept only normal video signals. A 75
Ω
termination is made unless the video output terminal is
connected.
connected.
#3 Video Output Connector (VIDEO OUT 1-8)
This BNC supplies a video signal looped through the
video input terminal.
Connectors 1-4 will output signals only when the
recorder is turned on.
video input terminal.
Connectors 1-4 will output signals only when the
recorder is turned on.
#4 Spot Output Connector (SPOT OUT)
This BNC supplies a full-screen live image signal to the
spot monitor while recording or not recording. No play-
back or split image, setup menu, or OSD information is
supplied via this connector.
spot monitor while recording or not recording. No play-
back or split image, setup menu, or OSD information is
supplied via this connector.
#5 Multiscreen Output Connector (MULTISCREEN OUT)
This BNC provides the multiscreen monitor with the fol-
lowing video.
lowing video.
• Live image: single spot, multi-split spot, single
sequence, quad-split sequence
• Playback image: single spot, multiscreen spot
• OSD information: camera title, time and date,
• OSD information: camera title, time and date,
recorder status, alarm status
The menu setup windows are also provided via this
BNC.
BNC.
#6 Alarm/Remote Port (ALARM/REMOTE)
This port accepts the alarm inputs 1 - 8, and remote
controls while supplying status outputs. See ALARM/
REMOTE Connection for details.
controls while supplying status outputs. See ALARM/
REMOTE Connection for details.
#7 RS232C Port (RS-232C)
This 9-pin port is used to communicate with the person-
al computer when controlling the recorder, or updating
the firmware installed in the recorder. See Serial Port
Connections for cable wiring, and RS-232C Communi-
cation Protocol.
al computer when controlling the recorder, or updating
the firmware installed in the recorder. See Serial Port
Connections for cable wiring, and RS-232C Communi-
cation Protocol.
#8 Mode Setup DIP Switch (MODE)
A 6-bit switch is used for such system setups as disk
formatting, PSD chain termination, and so forth. See DIP
Switch Setting for details.
formatting, PSD chain termination, and so forth. See DIP
Switch Setting for details.
#9 10Base-T/100Base-T (10/100BASE-T)
This port is used to exchange control data with Ethernet
via an Ethernet Hub.
via an Ethernet Hub.
$0 Data Port (DATA)
This port is used to communicate with external devices
compatible with the PSD (Panasonic Security Data) pro-
tocol based on RS485.
compatible with the PSD (Panasonic Security Data) pro-
tocol based on RS485.
$1 Cooling Fan
Prevents the temperature of the recorder from rising. Do
not block the ventilation openings.
not block the ventilation openings.
$2 Power Switch (POWER ON OFF)
This switch turns the power of the recorder on and off.
$3 Signal Ground Terminal (SIGNAL GND)
$4 Power Cord
Is connected to an AC outlet.