Panasonic wv-cw474 User Manual
#18
(0.83 mm
2
)
■
Connections
Note:
For the WV-CW474FE Colour CCTV Cameras, do not use a transformer larger than
10 VA.
1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry
seal until it has been ascertained that the unit is functioning.
CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY.
CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY.
2. To prevent fire or electric shock hazard, the UL listed wire VW-1 style 1007 should
be used for the cable for 24 V AC Input Terminals.
CAUTIONS
• Power supply connection
Recommended wire gauge sizes for 24 V AC line.
#24
(0.22 mm
2
)
Copper wire size
(AWG)
(AWG)
Length of cable
(Approx.)
(Approx.)
(m)
(ft)
#22
(0.33 mm
2
)
#20
(0.52 mm
2
)
20
30
45
75
65
100
160
260
24 V AC
Video Output Cable
To Video IN
(CAMERA IN)
(CAMERA IN)
BNC Plug
Green (Ground)
White (Neutral)
Black (Live)
BNC Plug
BNC Plug
■
Specifications
Dimensions:
133 mm (H) x 152.5 mm (D) [5-1/4” (H) x 6” (D)]
Weights:
1.1 kg (2.4 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
Specifications are subject to change without notice.
■
Standard Accessories
Tamperproof screw bit ...................................................................... 1 pc.
(1) Loosen the pan lock screw (stain-
less) with the Phillips screwdriver.
Panning becomes adjustable.
Panning becomes adjustable.
(2) Loosen the tilting lock screw
(stainless) with the Phillips screw-
driver.
Tilting becomes adjustable.
driver.
Tilting becomes adjustable.
Note:
Do not touch a black screw
placed on the opposite side.
(3) After adjusting panning and tilting,
tighten both of the lock screws
with the Phillips screwdriver.
with the Phillips screwdriver.
(4) Adjust the azimuth.
If the image is slanting, turn the azimuth adjuster to obtain a leveled image.
6. Adjust the focus.
Precautions:
• The focus adjustment should be done at the same time as the camera angle adjust-
ment.
• Set the zoom position to TELE before focusing.
(1) Loosen the focus lock screw by turning it counterclockwise.
The focus lock screw and the tip of the focus lever are identical with each other. The
focus lever becomes movable after loosening the focus lock screw.
focus lever becomes movable after loosening the focus lock screw.
(2) Adjust the focus by moving the focus lever to NEAR side or FAR side.
(3) Turn the focus lock screw clockwise to tighten the focus lever after adjustment.
Azimuth adjuster
TELE
Zoom lock screw
Focus lock screw
FAR
NEAR
WIDE
5. Adjust the panning, tilting and azimuth while watching the monitor.
Notes:
• You can check images by connecting an LCD monitor and such devices to the
monitor output jack.
However, images are not avail-
able on the monitor connected
to the video output cable.
However, images are not avail-
able on the monitor connected
to the video output cable.
• The camera will select ELC
(Electronic Light Control) mode
to make more precise focus
adjustment possible when an
LCD monitor is connected. You
will need careful focus adjust-
ment because the lens iris is
open in ELC mode.
to make more precise focus
adjustment possible when an
LCD monitor is connected. You
will need careful focus adjust-
ment because the lens iris is
open in ELC mode.
• Do not aim the camera at an
extremely bright object, as this
may cause smear and bloom-
ing.
may cause smear and bloom-
ing.
Pan lock screw
(stainless)
(stainless)
Tilting lock screw (stainless)
Monitor output jack (3.5 diam. minijack)
Panning table
Variable angles
plus or minus 75
plus or minus 75
°
(max.)
Camera mounting screw x 4
(included with WV-Q112E)
(included with WV-Q112E)
WV-Q112E
(option)
(option)
• Waterproofing Process
Apply waterproofing to the necessary portions, using appropriate materials.
a) Screw-holes, cable access holes, and gaps:
Fill these portions with silicon rubber or equivalent waterproofing material.
b) Cable joints:
• Use tape with electrical insulation and waterproof characteristics.
• Tape separately the three leads of the power cords, and cover the joint portions.
• Tape the joint portion of the video cables.
• Tape separately the three leads of the power cords, and cover the joint portions.
• Tape the joint portion of the video cables.
• Using Optional Bracket WV-Q112E
Secure the camera on the optional bracket using four screws included with the bracket.
Power cord
Video output cable
7. Adjust the zoom.
(1) Loosen the zoom lock screw by turning it counterclockwise.
The zoom lock screw and the tip of the zoom lever are identical with each other.
The zoom lever becomes movable after loosening the zoom lock screw.
The zoom lever becomes movable after loosening the zoom lock screw.
(2) Adjust the zoom by moving the zoom lever to TELE side or WIDE side.
(3) Turn the zoom lock screw clockwise to tighten the zoom lever after adjustment.
8. Reinstall the dome cover to the
main body by tightening three
dome cover mounting screws.
dome cover mounting screws.
(This procedure is also applicable to
cases where you replace the dome
cover with an optional Clear Dome
Cover WV-CW1CE.)
cases where you replace the dome
cover with an optional Clear Dome
Cover WV-CW1CE.)
Tighten the dome
cover mounting
screw x3
cover mounting
screw x3
2002 © Matsushita Communication Industrial Co., Ltd. All rights reserved
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/