Panasonic wv-cu360 User Manual
12
●
Parity Check Setting (02)
1. Select [Prty] by moving the joystick up or down.
2. Press the CAM/SET button. [Pr-n] appears.
3. Press the CAM/SET button.
4. Enter 1 (n) or 2 (E) using numeric buttons. Or, select the
2. Press the CAM/SET button. [Pr-n] appears.
3. Press the CAM/SET button.
4. Enter 1 (n) or 2 (E) using numeric buttons. Or, select the
desired parity check n (NONE) or E (EVEN) by moving
the joystick to the left or right.
The initial factory setting is NONE.
the joystick to the left or right.
The initial factory setting is NONE.
5. Press the CAM/SET button.
6. To return to [Prty], press MON/ESC button.
6. To return to [Prty], press MON/ESC button.
Note:
The desired parameter is also selected by press-
ing STILL/– button or EL-ZOOM/+ button.
●
Wait Time Setting (03)
1. Select [WAIt] by moving the joystick up or down.
2. Press the CAM/SET button. [oFF] appears.
3. Press the CAM/SET button.
4. Enter 1 (OFF), 2 (100), 3 (200), 4 (400), or 5 (1 000)
2. Press the CAM/SET button. [oFF] appears.
3. Press the CAM/SET button.
4. Enter 1 (OFF), 2 (100), 3 (200), 4 (400), or 5 (1 000)
using numeric buttons. Or, select the desired wait time
100, 200, 400, or 1 000 ms by moving the joystick to the
left or right. The initial factory setting is OFF (No retry).
100, 200, 400, or 1 000 ms by moving the joystick to the
left or right. The initial factory setting is OFF (No retry).
5. Press the CAM/SET button.
6. To return to [WAIt], press MON/ESC button.
6. To return to [WAIt], press MON/ESC button.
Note:
The desired parameter is also selected by press-
ing STILL/– button or EL-ZOOM+ button.
●
Controller Unit - Group Address Setting
[CU-gr] appears on the Setup menu, but leave the
default as it is.
default as it is.
●
System Unit - Group Address Setting
[SU-gr] appears on the Setup menu, but leave the
default as it is.
default as it is.
●
Unit Address Setting by UNIT A/UNIT
button (06)
button (06)
1. Select [UA-no] by moving the joystick up or down.
2. Press the CAM/SET button. [A1-01] appears.
3. Enter an UNIT A number (1 to 9) using Numeric but-
2. Press the CAM/SET button. [A1-01] appears.
3. Enter an UNIT A number (1 to 9) using Numeric but-
tons.
4. Press the CAM/SET button.
5. Enter a 2-digit unit address (01 to 99) using Numeric
5. Enter a 2-digit unit address (01 to 99) using Numeric
buttons.
6. Press the CAM/SET button.
7. To assign the other unit numbers, repeat procedures 3-
7. To assign the other unit numbers, repeat procedures 3-
6 after pressing CAM/SET button.
8. To return to [UA-no], press MON/ESC button.
Note:
System units with unit addresses 1 to 9 are
assigned to the UNIT A/UNIT button in numerical
order A1 to A9 as initial factory settings. (See page
18).
order A1 to A9 as initial factory settings. (See page
18).
●
Unit Address Setting by UNIT B button (07)
1. Select [Ub-no] by moving the joystick up or down.
2. Press the CAM/SET button. [b1-01] appears.
3. Enter an UNIT B number (1 to 9) using Numeric but-
2. Press the CAM/SET button. [b1-01] appears.
3. Enter an UNIT B number (1 to 9) using Numeric but-
tons.
4. Press the CAM/SET button.
5. Enter a 2-digit unit address (01 to 99) using numeric
5. Enter a 2-digit unit address (01 to 99) using numeric
buttons. The initial factory setting is [b1-01].
6. Press the CAM/SET button.
7. To assign the other unit numbers, repeat procedures 3-
7. To assign the other unit numbers, repeat procedures 3-
6 after pressing CAM/SET button.
8. To return to [Ub-no], press MON/ESC button.
Note:
System units with unit addresses 1 to 9 are
assigned to the UNIT B button in numerical order
B1 to B9 as initial factory settings (see page 18).
B1 to B9 as initial factory settings (see page 18).
●
User Password Setting (08)
1. Select [USrP] by moving the joystick up or down.
2. Press the CAM/SET button. [12345] appears.
3. Enter a 5-digit (00000 to 99999) using numeric buttons.
2. Press the CAM/SET button. [12345] appears.
3. Enter a 5-digit (00000 to 99999) using numeric buttons.
The LED blinks. The initial factory setting is [12345].
4. Press the CAM/SET button. The LED stops to blink.
5. To return to [USrP], press the MON/ESC button.
5. To return to [USrP], press the MON/ESC button.
Note:
If a 5-digit is not entered, the setting is invalid.
●
Administrator (Super User) Password
Setting (09)
Setting (09)
1. Select [SUSrP] by moving the joystick up or down.
2. Press the CAM/SET button. [12345] appears.
3. Enter a 5-digit (00000 to 99999) using numeric buttons.
2. Press the CAM/SET button. [12345] appears.
3. Enter a 5-digit (00000 to 99999) using numeric buttons.
The LED blinks. The initial factory setting is [12345].
4. Press the CAM/SET button. The LED stops to blink.
5. To return to [SUSrP], press the MON/ESC button.
5. To return to [SUSrP], press the MON/ESC button.
Note:
If a 5-digit is not entered, the setting is invalid.
●
User Authorization(Certification)Setting(10)
1. Select [USr-C] by moving the joystick up or down.
2. Press the CAM/SET button. [UC-on] appears.
3. Press the CAM/SET button
4. Enter 2 (User Certification ON) or 1 (User Certification
2. Press the CAM/SET button. [UC-on] appears.
3. Press the CAM/SET button
4. Enter 2 (User Certification ON) or 1 (User Certification
OFF) using Numeric buttons. Or, select User
Certification ON or OFF by moving the joystick to the
left or right. The initial factory setting is User
Certification ON.
Certification ON or OFF by moving the joystick to the
left or right. The initial factory setting is User
Certification ON.
5. Press the CAM/SET button.
6. To return to [USr-C], press MON/ESC button.
6. To return to [USr-C], press MON/ESC button.
Note:
The desired parameter is also selected by press-
ing STILL/– button or EL-ZOOM/+ button.
●
Camera Cleaning Setting (11)
Check that the power of the cameras and the other units
are switched on.
are switched on.
1. Select [CLEAn] by moving the joystick up or down.
2. Press the CAM/SET button [no-01] appears.
2. Press the CAM/SET button [no-01] appears.