JVC DR-DX5SE User Manual

Masterpage:Right+

Filename [DX5SEU_05Name.fm]

Page 19

Wednesday, 23 November 2005  14:13

If both Auto Channel Set and 
Auto Clock Set have been 
performed successfully, the 
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all 
necessary stations have been stored in the unit’s memory by using 
the PR +/– button(s).

●

If station names (ID – A pg. 88) have also been stored in the 
unit’s memory, the station name will be displayed at the top right 
corner of the TV screen for about 5 seconds when the unit is 
tuned to a different station.

●

If you want to set the tuner manually such as to add or skip 
channels, to change channel positions, or to set or change 
station names, see pages 75 – 76.

APR 1B (channel 

If both Auto Channel Set and Auto Clock Set have failed,         
A– –:– –B is displayed.

A Turn on the TV and select its AV mode, then make sure that all 

necessary stations have been stored in the unit’s memory by 
using the PR +/– button(s).

●

If station names (ID – A pg. 88) have also been stored in the 
unit’s memory, the station name will be displayed at the top right 
corner of the TV screen for about 5 seconds when the unit is 
tuned to a different station.

●

If you want to set the tuner manually such as to add or skip 
channels, to change channel positions, or to set or change 
station names, see pages 75 – 76.

B Perform AClock SetB (A pg. 77).
ATTENTION:After making sure the cables are connected properly, turn off the 
unit’s power once, then turn the unit’s power back on again.
The Country Set display appears on the TV screen; perform 

B (A pg. 17) or APreset DownloadB (A pg. 18) again.

●

To check if the Guide Programme numbers have been set 
correctly, perform the S

HOW

V

IEW

 Timer Programming. (A pg. 44)

●

In certain reception conditions, station names may not be stored 
correctly, and auto Guide Programme Number Set may not work 
properly. If the Guide Programme numbers are not set properly 
when you timer record a TV programme using the S

HOW

V

IEW

 

system, the unit will record a TV programme of a different station. 
When programming the timer using the S

HOW

V

IEW

 system, be 

sure to check the desired channel is selected correctly. 
(A pg. 44)

●

Your unit memorizes all detected stations even if reception of 
some of them is poor. You can delete those stations with an 
unacceptable picture. (A pg. 76, 

INFORMATION
Language for the on-screen display
Auto Set Up also selects the language automatically for the on-
screen display depending on the Country setting you have made in 
step 2 on page 17 (unless you have selected 

ABELGIUMB or 

ASUISSEB), as shown below.

If you want to change the language setting manually, see 

Just Clock
Your unit is equipped with the Just Clock function which provides 
accurate time keeping through automatic adjustments at regular 
intervals, by reading data from a PDC signal. If you want to take 
advantage of this function, simply set it to 

AONB. (A pg. 77)

When you connect the unit to your TV via a fully-wired 21-pin 
SCART cable (A pg. 16), the following functions are available. You 
can use these functions only with a TV offering T-V Link, etc.*
For details, refer to the instruction manual of your TV.

TV Auto Power On
The TV will turn on and be set to its AV mode automatically 
whenever you start playback.
For details, refer to the instruction manual of your TV.

Unit Auto Standby
You can use your TV’s remote control to turn off the unit.
For details, refer to the instruction manual of your TV.

Direct Rec
You can easily start recording the programme that you are 
watching on your TV. When you use this function, set 

B to AONB. (A pg. 72)

DX5SEU_00.book  Page 19  Wednesday, November 23, 2005  2:13 PM