JVC 0210TTH-SW-VP User Manual
59
1
Remove the filter cover
The filter is located at the front side of the projector
unit.
unit.
2
Remove the sponge and filter
Hold the center of the filter using your fingers, and pull
the filter toward you to remove it.
the filter toward you to remove it.
3
Clean the sponge and filter
Remove any dirt or dust using a vacuum cleaner.
CAUTION:
● Do not clean using a flammable air duster. This may
cause fire.
4
Mount the sponge and filter
Mount the filter and sponge to the projector using the
reverse removed procedure.
reverse removed procedure.
Finally, check to ensure that the filter cover is firmly
mounted.
mounted.
NOTE:
● Mount the filter correctly. Failure to do so may cause
the projector to malfunction.
● The projector may stop operating if a damaged filter or
filter panel is used. In this case, replace the filter or
filter panel with a new one.
filter panel with a new one.
Routine Servicing
Clean dirt on the cabinet
Do this with a soft cloth. In case of heavy soiling, soak a
cloth in neutral detergent diluted with water, wring dry
and wipe, followed by wiping again using a dry cloth.
Pay attention to the following to prevent the cabinet from
deteriorating in condition, getting damaged, or the paint
from coming off.
cloth in neutral detergent diluted with water, wring dry
and wipe, followed by wiping again using a dry cloth.
Pay attention to the following to prevent the cabinet from
deteriorating in condition, getting damaged, or the paint
from coming off.
● Do not wipe with a stiff cloth
● Do not wipe with force
● Do not wipe with thinner or benzene
● Do not spray volatile chemicals like insecticide
● Do not allow prolonged contact with rubber or
● Do not wipe with force
● Do not wipe with thinner or benzene
● Do not spray volatile chemicals like insecticide
● Do not allow prolonged contact with rubber or
plastic products
Remove dirt that is attached to the vent holes
Do this using a vacuum cleaner. Wipe using a cloth if a
vacuum cleaner cannot be used. Leaving dust attached
may prevent adjustment of the internal temperature and
result in malfunction of the projector.
vacuum cleaner cannot be used. Leaving dust attached
may prevent adjustment of the internal temperature and
result in malfunction of the projector.
Clean dirt on the lens
Do this using commercial blowers or lens cleaning
papers (for cleaning glasses and cameras).
Do not use fluid-type cleaning agents. This may lead to
peeling of the surface coating film.
Lens surface is fragile. Avoid rubbing or knocking it.
papers (for cleaning glasses and cameras).
Do not use fluid-type cleaning agents. This may lead to
peeling of the surface coating film.
Lens surface is fragile. Avoid rubbing or knocking it.
Replacement of Light Source
Lamp
Lamp
The light source lamp is a consumable item. Replace
with a new lamp unit if the image appears dull or if the
lamp burns out.
with a new lamp unit if the image appears dull or if the
lamp burns out.
● When the lamp needs to be replaced soon, users will
be notified through a message on the screen and the
indicator. (
indicator. (
● The life of the lamp used for this projector is about
2000 hours.
This is the average life of lamps, and not a guaranteed
value.
This is the average life of lamps, and not a guaranteed
value.
● The lamp life may not reach 2000 hours depending on
the operating conditions.
● Deterioration progresses rapidly when the remaining
lamp usable time is short.
● If the image is dark or color tone abnormal, replace the
lamp unit as soon as possible.
● For details on replacement of the lamp unit, please
consult your authorized dealer.
● Lamp has to be replaced by an authorized person.
Do not remove LAMP DOOR and lamp unit. This may
cause fire and electric shock hazards. Access to the
lamp unit only possible with use of tool.
cause fire and electric shock hazards. Access to the
lamp unit only possible with use of tool.