JVC rx-7012vsl User Manual
13
Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while
others will make operations easier.
others will make operations easier.
Recording a Source
For analog-to-analog recording
You can record any analog source through the receiver to —
• the cassette deck (or CD recorder) connected to the TAPE/CDR
• the cassette deck (or CD recorder) connected to the TAPE/CDR
jacks, and
• the VCR connected to the VCR jacks
— at the same time.
— at the same time.
For digital-to-digital recording
You can record the currently selected digital input through the
receiver to a digital recording device connected to the DIGITAL
OUT terminal.
receiver to a digital recording device connected to the DIGITAL
OUT terminal.
Notes:
• Analog-to-digital and digital-to-analog recordings are not possible.
• The output volume level, bass boost (see page 12), tone
• The output volume level, bass boost (see page 12), tone
adjustment (see page 12), and DSP modes (see page 20) cannot
affect the recording.
affect the recording.
• The test tone signal (see pages 23 and 24) does not come out
through the DIGITAL OUT terminal.
Adjusting the Front Speaker Output
Balance
Balance
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speaker output balance.
unequal, you can adjust the speaker output balance.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press ADJUST repeatedly until
“L/R BALANCE” appears on the
display.
display.
The display changes to show the current setting.
2. Press CONTROL UP
5/DOWN ∞
to adjust the balance.
• Pressing CONTROL UP
5 decreases the
left channel output from CNTR (Center)
to –21.
to –21.
• Pressing CONTROL DOWN
∞ decreases
the right channel output from CNTR
(Center) to –21.
(Center) to –21.
Changing the Source Name
When you have connected a CD recorder to the TAPE/CDR jacks or
the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name which will be shown on the display when
you select the CD recorder or DBS tuner as the source.
the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name which will be shown on the display when
you select the CD recorder or DBS tuner as the source.
On the front panel ONLY:
When changing the source name from “TAPE”
to “CDR”:
•
to “CDR”:
•
Press and hold TAPE/CDR/
SOURCE NAME to assign
“CDR.”
SOURCE NAME to assign
“CDR.”
When changing the source name from “TV
SOUND” to “DBS”:
•
SOUND” to “DBS”:
•
Press and hold TV SOUND/DBS/
SOURCE NAME to assign “DBS.”
SOURCE NAME to assign “DBS.”
To change the source name to “TAPE” or “TV SOUND,” repeat
the same procedure above — press and hold TAPE/CDR/SOURCE
NAME to select “TAPE” or TV SOUND/DBS/SOURCE NAME to
select “TV SOUND.”
the same procedure above — press and hold TAPE/CDR/SOURCE
NAME to select “TAPE” or TV SOUND/DBS/SOURCE NAME to
select “TV SOUND.”
Note:
Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
– “TAPE” or “TV SOUND” will appear on the display when you select
components. However, there may be some inconvenience.
– “TAPE” or “TV SOUND” will appear on the display when you select
the CD recorder or DBS tuner.
– You cannot use the digital input (see page 16) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
– You cannot use the COMPU LINK remote control system (see page
28) to operate the CD recorder.
TAPE/CDR
SOURCE NAME
CONTROL
DOWN
UP
ADJUST SETTING
TV SOUND/DBS
SOURCE NAME
EN10_19.RX-7012VSL[A]_f
01.4.25, 1:24 PM
13