packardbell easynote r Service Manual

Page of 27
Disassembly Manual

Summary of Contents of service manual for packardbell easynote r

  • Page 1

    Disassembly Manual

  • Page 2

    Table of contents Overview.................................................................................................................................................................3 Technician Notes....................................................................................................................................................3 Disassembly Instructions........................................................................................................................................3 Reassembly Instructions ........................................................................................................................................3 Required Tools .......................................................................................................................................................3 Hazardous Voltage .................................................................................................................................................4 Avoid Electrostatic...

  • Page 3: Required Tools

    Overview This document contains step-by-steps disassembly instructions for the EasyNote R series chassis. The instructions are illustrated where necessary with...

  • Page 4: Power Supply Unit

    WARNING Hazardous Voltage Ensure that the computer is disconnected from There is hazardous voltage present inside the computer its...

  • Page 5: Removing the Battery

    Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the unit. 2....

  • Page 6: Removing the Hard Disk Drive

    Fig. 2 Removing the battery Removing the Hard Disk Drive To remove the hard disk drive, first remove the...

  • Page 7: Removing the Optical Disk Drive

    2. Unscrew the HDD module and disconnect it as shown below 2 1 M2.5x7 Black Fig. 4 Disconnecting the...

  • Page 8: Removing the Memory Module

    Removing the Memory Module To remove the Memory Module, first remove the Battery then perform the following steps: 1. Release...

  • Page 9

    Fig. 9 Removing the screw retaining the memory module slot cover 2. Unclip the memory module as shown below...

  • Page 10: Removing the WLAN Module and MDC Modem Module

    Removing the WLAN Module and MDC Modem Module To remove the WLAN Module and MDC modem Module, first remove the...

  • Page 11: Removing the CPU

    Removing the CPU To remove the CPU, first remove the battery (see Removing the Battery), then perform the following steps...

  • Page 12

    Fig. 16 Removing the heat sink Fig. 17 Removing the heat sink Packard Bell EasyNote R Series Disassembly Manual...

  • Page 13

    3. Unlock the CPU and carefully remove it from the CPU socket as shown below Fig. 18 Unlocking the CPU...

  • Page 14: Removing the Keyboard

    Removing the Keyboard To remove the Keyboard, first remove the battery (see Removing the Battery), then perform the following steps:...

  • Page 15: Removing the Top Cover

    Removing the Top Cover To remove the Top Cover, first remove the battery (see Removing the Battery), remove the keyboard...

  • Page 16

    3. Flip over the unit and remove the screws then disconnect touch pad flat cable as shown below M2.5x7 Black...

  • Page 17: Removing the LCD Module

    Removing the LCD Module To remove the LCD Module, first remove the Battery (see Removing the Battery), remove the Top...

  • Page 18

    3. Release the LCD cable and WLAN antenna cable as shown below Fig. 27 Releasing the LCD cable and WLAN...

  • Page 19: Removing the LCD Panel

    Removing the LCD Panel To remove the LCD panel, first remove the LCD module (see Removing the LCD Module), then...

  • Page 20

    4. Unscrew all screws encircled below A = M2.5x5 Black B = M2.5x5 Silver C = M2x3.5 Black D =...

  • Page 21: Removing the Main Board

    Removing the Main Board To remove the main board, first remove the Bottom Cover (See Removing the Bottom Cover) then...

  • Page 22

    3. Release all screws as shown below and disconnect all speaker connection to Main Board. Actual mainboard layout may very...

  • Page 23: Removing the Multi Card Slot

    5. Remove two screws at the VGA port to separate Main Board from System Bracket. M3x7 Silver Fig. 37...

  • Page 24: Removing the Speaker Assembly

    Removing the Touch Pad To remove the touch pad, first remove the Top Cover (see Removing the Top Cover), then...

  • Page 25: DIP Switch Setting

    2. Carefully remove the Speaker assembly from System Bracket and place it aside. 3. Removing screws on Woofer as...

  • Page 26: Screws

    Screws M2x3.5 Black M2.5x7 Black M2x11 Silver M2x7 Silver M2.5x17 Black M2x3 Silver M2.5x5 Black M2.5x5 Silver M3x7 Silver M2x4...

  • Page 27

    Notice The information in this guide is subject to change without notice. This guide contains information protected by copyright. No...

downloadlike
ArtboardArtboardArtboard
Report Bug