Yamaha 007POTO-G0 User Manual
148
Using the Cue function
LS9-16/32 Owner’s Manual
This section explains how to use the LS9’s Cue function.
The LS9’s cue signals can be categorized into the follow-
ing three groups.
ing three groups.
1
INPUT CUE group
The cue signals of input channels make up this group. To
enable Cue for this group, press to turn on the [CUE] key
of a channel module to which an INPUT channel is
assigned or the [CUE] key of a ST IN channel.
enable Cue for this group, press to turn on the [CUE] key
of a channel module to which an INPUT channel is
assigned or the [CUE] key of a ST IN channel.
B
OUTPUT CUE group
The cue signals of output channels make up this group. To
switch to Cue for this group, press to turn on the [CUE]
key of the STEREO MASTER section or the [CUE] key
of a channel module to which a MIX/MATRIX/MONO
channel is assigned.
switch to Cue for this group, press to turn on the [CUE]
key of the STEREO MASTER section or the [CUE] key
of a channel module to which a MIX/MATRIX/MONO
channel is assigned.
C
Other CUE group
These are the Cue signals operated using buttons dis-
played in the screen. This group is enabled if you turn on a
CUE button in a RACK screen to which you’ve assigned
an effect, the CUE button of the RECORDER screen, or
the KEY IN CUE button of the DYNAMICS 1/2 popup
window. This group will automatically be disabled when
you exit the corresponding screen.
played in the screen. This group is enabled if you turn on a
CUE button in a RACK screen to which you’ve assigned
an effect, the CUE button of the RECORDER screen, or
the KEY IN CUE button of the DYNAMICS 1/2 popup
window. This group will automatically be disabled when
you exit the corresponding screen.
It is not possible to simultaneously turn on Cue between
different groups. Normally, the group to which the most
recently pressed [CUE] key (or a CUE/KEY IN CUE but-
ton in the screen) belongs will take priority, and the [CUE]
keys of the previously selected group will be defeated.
However if you switch the Cue signal group in a specific
order, the state of the [CUE] keys of the previously-
selected group will be restored when the current Cue sig-
nal is defeated.
different groups. Normally, the group to which the most
recently pressed [CUE] key (or a CUE/KEY IN CUE but-
ton in the screen) belongs will take priority, and the [CUE]
keys of the previously selected group will be defeated.
However if you switch the Cue signal group in a specific
order, the state of the [CUE] keys of the previously-
selected group will be restored when the current Cue sig-
nal is defeated.
The following illustration shows the priority order of the
[CUE] keys. After you have switched groups from lower
to upper levels, if you then defeat Cue for the upper group,
the previous [CUE] key status of the group immediately
below will be restored.
[CUE] keys. After you have switched groups from lower
to upper levels, if you then defeat Cue for the upper group,
the previous [CUE] key status of the group immediately
below will be restored.
For example if you switch groups in the order of OUT-
PUT CUE group
PUT CUE group
→ INPUT CUE group → Other CUE
group, you can then successively defeat the [CUE] keys
(CUE/KEY IN CUE buttons) to successively restore the
[CUE] key status of the previously selected group. How-
ever, if the CUE MODE is LAST CUE, the state of the
[CUE] key is not reproduced.
(CUE/KEY IN CUE buttons) to successively restore the
[CUE] key status of the previously selected group. How-
ever, if the CUE MODE is LAST CUE, the state of the
[CUE] key is not reproduced.
Using the Cue function
About cue groups
[CUE] key of a channel module to
which an INPUT channel is assigned
which an INPUT channel is assigned
[CUE] key of a ST IN channel
[CUE] key of the STEREO channel
[CUE] key of a channel module to which a
MIX/MATRIX/MONO channel is assigned
MIX/MATRIX/MONO channel is assigned
CUE button in the screen
Other CUE group
INPUT CUE group
OUTPUT CUE group