Yamaha 007POTO-G0 User Manual
153
Using the oscillator
LS9-16/32 Owner’s Manual
15
T
alkbac
k / Oscillator
Here’s how you can send a sine wave or pink noise from the internal oscillator to the desired bus.
1
In the DISPLAY ACCESS section, press the
[MONITOR] button repeatedly to access the
OSCILLATOR screen.
[MONITOR] button repeatedly to access the
OSCILLATOR screen.
In the OSCILLATOR screen you can check the set-
tings of the oscillator and turn it on/off.
tings of the oscillator and turn it on/off.
1
OUTPUT button
This switches the oscillator on/off.
B
MODE field
Move the cursor to a button in this field to select the
desired type of oscillator.
desired type of oscillator.
C
Parameter field
Here you can adjust the parameters of the oscillator
you selected in the MODE field. Use the dial or the
[DEC]/[INC] keys to operate the knobs shown in the
field.
you selected in the MODE field. Use the dial or the
[DEC]/[INC] keys to operate the knobs shown in the
field.
D
Oscillator level
This indicates the output level of the oscillator.
E
ASSIGN field
This selects the buses to which the oscillator signal
will be sent. If you want to clear all selections, move
the cursor to the CLEAR ALL button and press the
[ENTER] key.
will be sent. If you want to clear all selections, move
the cursor to the CLEAR ALL button and press the
[ENTER] key.
2
Use the buttons in the MODE field to select
the type of signal you want to output.
the type of signal you want to output.
You can choose from the following signals.
3
If you want to adjust the oscillator parame-
ters, use the dial or the [DEC]/[INC] keys to
operate the knobs shown in the field.
ters, use the dial or the [DEC]/[INC] keys to
operate the knobs shown in the field.
The parameters shown in the parameter field will
depend on the type of oscillator selected in the MODE
field.
The following table lists the oscillator types and the
parameters displayed for each type.
depend on the type of oscillator selected in the MODE
field.
The following table lists the oscillator types and the
parameters displayed for each type.
The following table describes each parameter in detail.
4
Using the buttons in the ASSIGN field,
select the bus(es) to which you want to
send the oscillator signal. (You may select
more than one.)
select the bus(es) to which you want to
send the oscillator signal. (You may select
more than one.)
The buttons correspond to the following buses.
Using the oscillator
SINE WAVE 1CH
Sine wave, one channel
PINK NOISE
Pink noise
BURST NOISE
Burst noise (intermittently output pink
noise)
noise)
3
1
5
2
4
Oscillator type
Parameters
SINE WAVE 1CH
LEVEL, FREQ
PINK NOISE
LEVEL, HPF, LPF
BURST NOISE
LEVEL, HPF, LPF, WIDTH, INTERVAL
Parameter
Details
LEVEL
Oscillator output level
FREQ
Frequency of the sine wave produced
by the oscillator
by the oscillator
HPF
High-pass filter (on/off switch, cutoff
frequency)
frequency)
LPF
Low-pass filter (on/off switch, cutoff fre-
quency)
quency)
WIDTH
Duration of the noise
INTERVAL
Length of silence between noise bursts
MIX 1–16 buttons
MIX buses 1–16
MATRIX 1–8 but-
tons
tons
MATRIX buses 1–8
ST L, ST R, MONO
buttons
buttons
STEREO bus L/R, MONO bus
Level
The BURST NOISE button is on
WIDTH
INTERVAL
Pink noise output
Time
• If you want to clear all selections, move the cursor to the
CLEAR ALL button and press the [ENTER] key.
HINT