Yamaha 007POTO-G0 User Manual
184
Using control changes to control parameters
LS9-16/32 Owner’s Manual
B
CONTROL CHANGE MODE field
Here you can select the control change transmission/
reception mode. This setting is linked with the CON-
TROL CHANGE MODE field of the MIDI SETUP
popup window.
reception mode. This setting is linked with the CON-
TROL CHANGE MODE field of the MIDI SETUP
popup window.
C
List
This list shows the event (fader/encoder pattern, [ON]
key on/off operation, etc.) assigned to each control
number.
key on/off operation, etc.) assigned to each control
number.
●
NO.
This indicates the control number. You can use
control numbers 1–31, 33–95, and 102–119.
control numbers 1–31, 33–95, and 102–119.
●
CONTROL CHANGE EVENT
Indicates/selects the type of event assigned to each
control number. When you press the popup button
for an event, the CONTROL CHANGE EVENT
popup window will appear, allowing you to change
the control number assignment.
control number. When you press the popup button
for an event, the CONTROL CHANGE EVENT
popup window will appear, allowing you to change
the control number assignment.
D
CLEAR ALL button
Pressing this button will clear all event assignments in
the list.
the list.
E
INITIALIZE ALL button
Pressing this button will restore all event assignments
in the list to their default state.
in the list to their default state.
7
Use the buttons of the CONTROL CHANGE
MODE field to select the control change
transmission/reception mode.
MODE field to select the control change
transmission/reception mode.
You can choose one of the following two modes for
control change transmission/reception.
control change transmission/reception.
●
NRPN mode (when the NRPN button is on)
The LS9’s various mix parameters will be transmitted
and received on a single MIDI channel as NRPN mes-
sages. If you select this mode, the assignments in the
list will be ignored.
and received on a single MIDI channel as NRPN mes-
sages. If you select this mode, the assignments in the
list will be ignored.
●
TABLE mode (when the TABLE button is on)
The LS9’s various mix parameters will be transmitted
and received on a single MIDI channel as control
change messages.
and received on a single MIDI channel as control
change messages.
8
Use the buttons of the CONTROL CHANGE
field to turn transmission and reception on/
off, and make settings for echo output.
field to turn transmission and reception on/
off, and make settings for echo output.
Each button has the following function.
●
Tx button
Switches control change transmission on/off.
●
Rx button
Switches control change reception on/off.
●
ECHO button
This selects whether incoming control changes are
echoed-out from the transmission port.
echoed-out from the transmission port.
9
To change the event assignment for each
control number, move the cursor to the
popup button for the corresponding event
in the list, and press the [ENTER] key.
control number, move the cursor to the
popup button for the corresponding event
in the list, and press the [ENTER] key.
The CONTROL CHANGE EVENT popup window
will appear. In this window you can specify the event
assigned to each control number. The window contains
the following items.
will appear. In this window you can specify the event
assigned to each control number. The window contains
the following items.
1
MODE field
Select the type of event.
B
PARAMETER 1/2 field
In conjunction with the MODE field, this specifies the
type of event.
type of event.
10
In the order of the MODE field
→ PARAME-
TER 1 field
→ PARAMETER 2 field, specify
the type of event you want to assign.
To select an item, use the dial or the [DEC]/[INC]
keys. Move the cursor to the OK button and press the
[ENTER] key to finalize the changes and close the
CONTROL CHANGE EVENT popup window.
keys. Move the cursor to the OK button and press the
[ENTER] key to finalize the changes and close the
CONTROL CHANGE EVENT popup window.
11
Assign events to other control numbers in
the same way.
the same way.
When you operate the parameters you assigned on the
LS9, control change messages will be transmitted to
external devices. Similarly, if the corresponding con-
trol change messages are sent from an external device
on the appropriate channel, the parameters assigned to
those control numbers will change.
LS9, control change messages will be transmitted to
external devices. Similarly, if the corresponding con-
trol change messages are sent from an external device
on the appropriate channel, the parameters assigned to
those control numbers will change.
• The channel on which control changes are transmitted and
received is specified by the MIDI SETUP popup window
PORT/CH field (
PORT/CH field (
HINT
1
2
• If NRPN mode is selected as the control change transmis-
sion/reception mode, the settings in this window are ignored.
NOTE
• For details on the events that can be assigned to control
changes, refer to the appendix (
HINT
• You can use the CLEAR ALL button to erase all assignments
to control numbers. The INITIALIZE ALL button will return all
control number assignments to their default state.
control number assignments to their default state.
• Assignments to control numbers are maintained as settings
for the entire system, rather than for individual scenes.
HINT