Yamaha 007POTO-G0 User Manual
99
9
Input/output patching
Changing the input patching
LS9-16/32 Owner’s Manual
When the LS9 is in the initial state, the following input ports (jacks / internal ports) are patched to
each input channel.
each input channel.
However, the above patching can be modified as needed.
Here’s how to change the patching of each input channel.
Here’s how to change the patching of each input channel.
1
Press the [HOME] key to access the
SELECTED CH VIEW screen, and use the
[SEL] keys to select an input channel.
SELECTED CH VIEW screen, and use the
[SEL] keys to select an input channel.
1
Channel number / Channel name
B
HA popup button
C
Port select popup button
2
Move the cursor to the HA popup button in
the screen, and press the [ENTER] key.
the screen, and press the [ENTER] key.
The HA/PATCH popup window will appear. In this
popup window, you can view the input port and name
selected for each input channel, turn the phantom
power on/off, adjust the gain, and switch between nor-
mal/reversed phase, in groups of eight channels.
popup window, you can view the input port and name
selected for each input channel, turn the phantom
power on/off, adjust the gain, and switch between nor-
mal/reversed phase, in groups of eight channels.
1
Channel number
This is the number of the input channel.
B
Channel name
This is the name of the input channel.
C
Port select popup button
This button selects the input port assigned to the chan-
nel. The currently selected input port is shown.
nel. The currently selected input port is shown.
D
+48V button
This button switches the phantom power on (red) or
off (black) for the head amp assigned to that channel.
off (black) for the head amp assigned to that channel.
E
GAIN knob
This indicates the amount of gain for the head amp
assigned to that channel. Move the cursor to the knob
and use the dial or the [DEC]/[INC] keys to adjust the
setting. The level meter located immediately to the
right of the knob shows the input level of the corre-
sponding port.
assigned to that channel. Move the cursor to the knob
and use the dial or the [DEC]/[INC] keys to adjust the
setting. The level meter located immediately to the
right of the knob shows the input level of the corre-
sponding port.
F
ø
(phase) button
This button switches the head amp assigned to that
channel between normal phase (black) and reverse
phase (orange).
channel between normal phase (black) and reverse
phase (orange).
Changing the input patching
For the LS9-16
Input channels
Input port (jack / internal port)
INPUT channels 1–16
INPUT jacks 1–16
INPUT channels 17–32
Slot input channels 1–16
ST IN channels 1–4 (L/R)
Rack outputs 5–8 (L/R)
For the LS9-32
Input channels
Input port (jack / internal port)
INPUT channels 1–32
INPUT jacks 1–32
INPUT channels 33–48
Slot 1 input channels 1–16
INPUT channels 49–64
Slot 2 input channels 1–16
ST IN channels 1–4 (L/R)
Rack outputs 5–8 (L/R)
1
2
3
• As an alternative to using the HA popup button, you can also
select the input port in the PATCH/NAME popup window that
appears when you move the cursor to the port select popup
button and press the [ENTER] key (
appears when you move the cursor to the port select popup
button and press the [ENTER] key (
HINT
1
2
3
4
4
5
6
• The PAD will be internally switched on or off when the HA
gain is adjusted between -14 dB and -13 dB. Keep in mind
that noise may be generated if there is a difference between
the Hot and Cold output impedance of the external device
connected to the INPUT connector when using phantom
power.
that noise may be generated if there is a difference between
the Hot and Cold output impedance of the external device
connected to the INPUT connector when using phantom
power.
NOTE