Yamaha 007POTO-G0 User Manual
216
Setting the network address
LS9-16/32 Owner’s Manual
Here’s how to set the network address that will be required when you use the LS9’s NETWORK
connector to connect it to a Windows computer.
connector to connect it to a Windows computer.
1
In the DISPLAY ACCESS section, press the
[SETUP] key repeatedly to access the MISC
SETUP screen.
[SETUP] key repeatedly to access the MISC
SETUP screen.
1
NETWORK field
This shows the values of network-related parameters.
B
NETWORK SET button
This accesses the NETWORK popup window, where
you can make network-related settings.
you can make network-related settings.
C
MAC ADDRESS field
This is the MAC (Machine Access Control) address
specified for identifying a host within a network. This
field is only for display, and cannot be edited.
specified for identifying a host within a network. This
field is only for display, and cannot be edited.
2
Move the cursor to the NETWORK SET but-
ton in the NETWORK field, and press the
[ENTER] key to access the NETWORK
popup window.
ton in the NETWORK field, and press the
[ENTER] key to access the NETWORK
popup window.
1
IP ADDRESS field
This is a number (IP address) assigned to identify each
device on the Internet or within an LAN (Local Area
Network).
device on the Internet or within an LAN (Local Area
Network).
B
GATEWAY ADDRESS field
This specifies the number (gateway address) that iden-
tifies a device (gateway) that allows data of differing
media or protocol to be exchanged within a network to
allow communication.
tifies a device (gateway) that allows data of differing
media or protocol to be exchanged within a network to
allow communication.
C
SUBNET MASK field
This defines the number of bits (of the IP address used
within the network) that will be used as the network
address that distinguishes the network.
within the network) that will be used as the network
address that distinguishes the network.
D
LINK MODE field
Select either 100BASE-TX (transmission speed: max-
imum 100 Mbps) or 10BASE-T (transmission speed:
max 10 Mbps) as the specification used for communi-
cation via the NETWORK connector.
imum 100 Mbps) or 10BASE-T (transmission speed:
max 10 Mbps) as the specification used for communi-
cation via the NETWORK connector.
3
Move the cursor to the LINK MODE field,
and use the dial or the [DEC]/[INC] keys to
select a communication protocol for the
NETWORK connector as appropriate for the
network to which the LS9 is connected.
and use the dial or the [DEC]/[INC] keys to
select a communication protocol for the
NETWORK connector as appropriate for the
network to which the LS9 is connected.
4
Move the cursor to each remaining field in
the screen, and use the dial or the [DEC]/
[INC] keys to specify each address.
the screen, and use the dial or the [DEC]/
[INC] keys to specify each address.
If you are connecting the LS9 to your computer in a
one-to-one connection, we recommend that you make
the following initial settings.
one-to-one connection, we recommend that you make
the following initial settings.
●
IP address
192.168.0.128 or similar (it must not conflict with the
IP address of any other device on the network)
IP address of any other device on the network)
●
Gateway address
192.168.0.1 or similar (it must not conflict with the IP
address of any other device on the network)
address of any other device on the network)
●
Subnet mask
255.255.255.0 or similar
Setting the network address
• The network address can be changed only by users who have administrative privileges.
• For details on network settings, refer to the LS9 Editor installation guide which can be downloaded from the following Yamaha website.
NOTE
1
LS9-32
2
3
1
3
2
4
• Be aware that if the specification does not match, communi-
cation will not occur correctly.
NOTE