Yamaha aw4416e6 User Manual
E
! Important !
— You must read this —
Limitations on simultaneous
use of I/O cards
The rear panel of the AW4416 has two OPTION I/O slots,
allowing you to install various I/O cards that are compatible
with the Yamaha Mini YGDAI format.
The combinations of I/O cards shown in the table below can-
not be installed in the AW4416’s OPTION I/O slots 1/2 and
used simultaneously. (However, the Y56K card can be used in
combination with the three models marked by a symbol.)
Combinations of I/O card that cannot be used together
allowing you to install various I/O cards that are compatible
with the Yamaha Mini YGDAI format.
The combinations of I/O cards shown in the table below can-
not be installed in the AW4416’s OPTION I/O slots 1/2 and
used simultaneously. (However, the Y56K card can be used in
combination with the three models marked by a symbol.)
Combinations of I/O card that cannot be used together
: Can be used together
Using cards together in violation of the above restrictions will
cause the AW4416 to be damaged. You must observe the
restrictions described above. Please be aware that if an
impermissible combination of cards is used inadvertently,
Yamaha Corporation will take no responsibility for the dam-
age that will occur.
cause the AW4416 to be damaged. You must observe the
restrictions described above. Please be aware that if an
impermissible combination of cards is used inadvertently,
Yamaha Corporation will take no responsibility for the dam-
age that will occur.
If an impermissible combination of I/O cards is used inadvert-
ently, a message of “CANNOT USE BOTH SLOTS!!” will
appear in the display, either as shown in the form shown in
ently, a message of “CANNOT USE BOTH SLOTS!!” will
appear in the display, either as shown in the form shown in
1
or
2
, below.
Message
1
Message
2
If you continue using the AW4416 in this state, it will be dam-
aged.
aged.
Turn off the power in the following sequence.
1. The monitor system connected to the output jacks of the
1. The monitor system connected to the output jacks of the
AW4416
2. The AW4416 itself
3. Storage devices connected to the SCSI connector of the
3. Storage devices connected to the SCSI connector of the
AW4416, and external sound sources connected to its
input/output jacks.
input/output jacks.
You must perform the shutdown procedure (Operation Guide
p.17) before you turn off the power of the AW4416.
p.17) before you turn off the power of the AW4416.
However if display message
1
is shown
, you will be unable to
perform the shutdown procedure, so make sure that the access
indicator located at the left of the level meter/counter is not lit,
and then turn off the power.
indicator located at the left of the level meter/counter is not lit,
and then turn off the power.
Do not turn on the power until a permissible combination of
I/O cards is installed.
I/O cards is installed.
• The limitation on the use of I/O cards is not dependent on
the version of the AW4416’s operating system. However,
please be aware that if you are using an operating system
version earlier than V2.0, the error messages shown above
may not appear.
please be aware that if you are using an operating system
version earlier than V2.0, the error messages shown above
may not appear.
• This document (“You must read this”) is current as of Octo-
ber 2001. To confirm operation of option I/O cards that
become available in the future, refer to the AW4416 home
page www.aw4416.com.
become available in the future, refer to the AW4416 home
page www.aw4416.com.
• If you have questions regarding this matter, please consult
your Yamaha dealer.
AP8AD
(Apogee
Corporation)
AP8DA
(Apogee
Corporation)
Y56K
(WAVES
Corporation)
MY8-TD
MY8-AT
MY8-AE
MY4-AD
MY8-AD
MY4-DA
AP8AD
AP8DA
Y56K