Yamaha EMX3000 User Manual
6
Front and rear panel
EMX3000—Owner’s Manual
Input/output panel
1
Channel input jacks (MIC, LINE) 1~8
These are the input jacks for channels 1~8.
These are the input jacks for channels 1~8.
By using the GAIN control (control panel 1)
you can connect any of the jacks to a wide range
of sources, from mics to line-level devices
(including synthesizers and rhythm machines).
The MIC jacks can provide +48V phantom
power, allowing you to use condenser micro-
phones.
you can connect any of the jacks to a wide range
of sources, from mics to line-level devices
(including synthesizers and rhythm machines).
The MIC jacks can provide +48V phantom
power, allowing you to use condenser micro-
phones.
Both MIC and LINE are balanced.
They are compatible with microphones of output
impedance 50~600
impedance 50~600
Ω
or line level devices of
600
Ω
. The nominal input level is –34 dB~+10 dB
for the LINE jacks, and –60 dB~–16 dB for the
MIC jacks.
MIC jacks.
Pin connections for the MIC and LINE jacks are
as follows:
as follows:
* You can also connect a normal unbalanced phone plug.
2
INSERT I/O (insert) jacks 1~4
These are TRS phone jacks that enable you to
insert an external effect processor, such as a com-
pressor/limiter, between the equalizer and fader
of input channels 1~4. These connections require
a special “Y” cable, such as shown in the follow-
ing diagram. The nominal input/output levels are
0 dB.
These are TRS phone jacks that enable you to
insert an external effect processor, such as a com-
pressor/limiter, between the equalizer and fader
of input channels 1~4. These connections require
a special “Y” cable, such as shown in the follow-
ing diagram. The nominal input/output levels are
0 dB.
0
A
I O
I O
I O
I O
A
A
A
A
B
B
B
B
ST
SUB 1
SUB 1
ST
SUB 2
SUB 2
+4dB
+4dB
TAPE
REC
ST 1
-10dBV
-10dBV
+4dB
ST 2
+4dB
+4dB
+4dB
+4dB
+4dB
MONI
MONI
MONO
EFFECT
FOOT SW
1
2
BRIDGE
P.AMP
IN
C-R
PHONES
PHONES
9 L
11 L
L
L
L
R
L
R
R
L
9 L
10 R
12 R
R
R
10 R
11 L
12 R
(MONO)
(MONO)
(MONO)
(MONO)
9 10
11 12
INPUT
OUTPUT
L
R
L
R
1
2
3
4
5
6
7
8
INSERT
LINE
INSERT
LINE
INSERT
LINE
INSERT
LINE
LINE
LINE
LINE
LINE
MIC
MIC
MIC
MIC
MIC
MIC
MIC
MIC
INSERT
OUT IN
0dB
I O
B
9
3
4
2
6
C
8
5 7
1
MIC jacks
(XLR type)
LINE jacks
(TRS phone jacks) *
Pin 1: ground
Sleeve: ground
Pin 2: hot (+)
Tip: hot (+)
Pin 3: cold (–)
RIng: cold (–)
GND
R
S
T
+
-
GND
+
-
1
2
3
Note: It is not possible to simultaneously use
both the MIC and LINE inputs of a given chan-
nel. For each channel, use only one of the in-
puts as appropriate for the input source.
Phantom power is switched on/off simulta-
neously for channels 1~8. For this reason, de-
vices (in particular, unbalanced devices) other
than condenser microphones must be connect-
ed to the LINE input jacks of channels 1~8 or
channel 9/10~11/12 input jacks if the PHAN-
TOM +48V switch (control panel Y) is on.
both the MIC and LINE inputs of a given chan-
nel. For each channel, use only one of the in-
puts as appropriate for the input source.
Phantom power is switched on/off simulta-
neously for channels 1~8. For this reason, de-
vices (in particular, unbalanced devices) other
than condenser microphones must be connect-
ed to the LINE input jacks of channels 1~8 or
channel 9/10~11/12 input jacks if the PHAN-
TOM +48V switch (control panel Y) is on.
to the input jack of
the external processor
the external processor
to the output jack of
the external processor
the external processor
to the INSERT I/O jack
Tip
Tip
Ring
Sleeve
Sleeve