Yamaha KX25 User Manual
Setting Up
Owner’s Manual
14
For Windows:
1.
Make sure that the power to the KX is turned
off.
off.
2.
Disconnect all MIDI cables that connect MIDI
devices to MIDI IN/OUT connectors on the
KX.
devices to MIDI IN/OUT connectors on the
KX.
3.
Start the computer and log on to the
Administrator account.
Administrator account.
4.
Insert the TOOLS for KX DVD-ROM into the
DVD-ROM drive.
DVD-ROM drive.
5.
Open the “Extensions for Steinberg DAW”
folder in the DVD-ROM, then double-click
the file “setup.exe”
The first display for installing Extensions for
Steinberg DAW appears.
folder in the DVD-ROM, then double-click
the file “setup.exe”
The first display for installing Extensions for
Steinberg DAW appears.
6.
Click [Next] to call up the InstallShield
Wizard for Yamaha Extensions for Steinberg
DAW.
Wizard for Yamaha Extensions for Steinberg
DAW.
7.
Click [Next] to start the installation.
To cancel the installation procedure, click
[Cancel].
To cancel the installation procedure, click
[Cancel].
8.
When the installation is complete, a
message indicating so appears. Click
[Finish].
message indicating so appears. Click
[Finish].
9.
After disconnecting all other USB devices
from the computer, connect the KX directly
to the computer (without using a hub) by
using a USB cable.
from the computer, connect the KX directly
to the computer (without using a hub) by
using a USB cable.
10.
Turn the power on of the KX by pressing the
[STANDBY/ON] switch.
The KX will be recognized by the connected
computer.
[STANDBY/ON] switch.
The KX will be recognized by the connected
computer.
11.
Install the USB-MIDI driver.
The installation is now complete.
Important!
Make sure to use the same USB connector as the
one used in the installation procedure when you
connect the KX and the Windows computer again. If
you connect the USB cable to a different connector,
you will have to install the USB-MIDI driver again.
one used in the installation procedure when you
connect the KX and the Windows computer again. If
you connect the USB cable to a different connector,
you will have to install the USB-MIDI driver again.
NOTE
Make sure to install Cubase 4, Cubase
Studio 4, or Cubase AI4 before installing
Extensions for Steinberg DAW described in
step 5 below.
Studio 4, or Cubase AI4 before installing
Extensions for Steinberg DAW described in
step 5 below.
NOTE
· If the same version of Extensions for
Steinberg DAW has already been
installed in your computer, a window
appears indicating completion. In this
case, click [Finish].
installed in your computer, a window
appears indicating completion. In this
case, click [Finish].
· If a newer version of Extensions for
Steinberg DAW has already been
installed in your computer, a dialog box
appears indicating that the newer
software has already been installed. In
this case, you do not need to install the
software. Click [OK] in the dialog box.
installed in your computer, a dialog box
appears indicating that the newer
software has already been installed. In
this case, you do not need to install the
software. Click [OK] in the dialog box.
· If an older version of Extensions for
Steinberg DAW has been installed in your
computer, the software should be
updated. (The procedure is the same as
for installing it from scratch.)
computer, the software should be
updated. (The procedure is the same as
for installing it from scratch.)
NOTE
During the installation procedure, you can
select the type of Extensions for Steinberg
DAW by selecting “Custom” in the Setup
Type dialog.
select the type of Extensions for Steinberg
DAW by selecting “Custom” in the Setup
Type dialog.
NOTE
Installation of the USB MIDI driver is
described in “installationguide_en.pdf”
stored in the “USB-MIDI_Driver” folder.
described in “installationguide_en.pdf”
stored in the “USB-MIDI_Driver” folder.
USB connector
USB cable
KX rear panel