Yamaha RX-V1600 User Manual
98
ZONE 2/ZONE 3
■ Using the internal amplifiers of this unit
If you want to use one internal amplifier (surround or surround back) of this unit
Connect the Zone 2 or Zone 3 speakers directly to the SURROUND/ZONE 2(3) or PRESENCE/ZONE 2(3) speaker
terminals and select either SUR or PRNS for ZONE2 AMP or ZONE3 AMP (see pages 80 and 81).
Connect the Zone 2 or Zone 3 speakers directly to the SURROUND/ZONE 2(3) or PRESENCE/ZONE 2(3) speaker
terminals and select either SUR or PRNS for ZONE2 AMP or ZONE3 AMP (see pages 80 and 81).
If you want to use two internal amplifiers (both surround and surround back) of this unit
Connect the Zone 2 or Zone 3 speakers directly to the SURROUND/ZONE 2(3) and PRESENCE/ZONE 2(3) speaker
terminals and select BOTH for ZONE2 AMP or ZONE3 AMP (see pages 80 and 81).
Connect the Zone 2 or Zone 3 speakers directly to the SURROUND/ZONE 2(3) and PRESENCE/ZONE 2(3) speaker
terminals and select BOTH for ZONE2 AMP or ZONE3 AMP (see pages 80 and 81).
You can select the zone you want to control by using the
control buttons on the front panel or on the remote control.
Once the zone you want to control is selected, you can
control the selected zone as described in “Controlling Zone 2 and Zone 3” on page 99.
control buttons on the front panel or on the remote control.
Once the zone you want to control is selected, you can
control the selected zone as described in “Controlling Zone 2 and Zone 3” on page 99.
■ Front panel operations
1
Press MAIN ZONE ON/OFF, ZONE 2 ON/OFF
or ZONE 3 ON/OFF on the front panel to
individually turn on this unit, Zone 2 or Zone
3.
Press each button repeatedly to turn on the respective
zone or set it to the standby mode.
or ZONE 3 ON/OFF on the front panel to
individually turn on this unit, Zone 2 or Zone
3.
Press each button repeatedly to turn on the respective
zone or set it to the standby mode.
y
Once MASTER ON/OFF on the front panel is pressed
inward to the ON position, you can also press POWER and
STANDBY on the remote control to turn on this unit, Zone
2 and Zone 3 simultaneously.
inward to the ON position, you can also press POWER and
STANDBY on the remote control to turn on this unit, Zone
2 and Zone 3 simultaneously.
2
Press ZONE CONTROL on the front panel
repeatedly to select the zone you want to
control.
repeatedly to select the zone you want to
control.
Each time you press ZONE CONTROL, the front
panel display changes as shown below, and the
indicator for the currently selected zone flashes for
approximately 5 seconds. However, no indicator
flashes when this unit is selected.
panel display changes as shown below, and the
indicator for the currently selected zone flashes for
approximately 5 seconds. However, no indicator
flashes when this unit is selected.
ZONE2
Controls the Zone 2 component connected to the
ZONE 2 AUDIO L/R jacks on the rear panel of this
unit.
Controls the Zone 2 component connected to the
ZONE 2 AUDIO L/R jacks on the rear panel of this
unit.
ZONE3
Controls the Zone 3 component connected to the
ZONE 3 AUDIO L/R jacks on the rear panel of this
unit.
Controls the Zone 3 component connected to the
ZONE 3 AUDIO L/R jacks on the rear panel of this
unit.
IMPORTANT SAFETY NOTICE
SURROUND/ZONE 2(3) or PRESENCE/ZONE 2(3) speaker terminals of this Receiver should not be connected to a
Passive Loudspeaker Selector Box or more than one loudspeaker per channel.
Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low
impedance load resulting in amplifier damage. See this owner’s manual for correct usage.
Compliance with minimum speaker impedance information for all channels must be maintained at all times. This
information is found on the back panel of your Receiver.
Passive Loudspeaker Selector Box or more than one loudspeaker per channel.
Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low
impedance load resulting in amplifier damage. See this owner’s manual for correct usage.
Compliance with minimum speaker impedance information for all channels must be maintained at all times. This
information is found on the back panel of your Receiver.
R
L
+
–
PRESENCE/ ZONE 2(3)
SINGLE
R
L
+
–
+
–
+
+
–
–
SURROUND BACK
SURROUND/ZONE 2(3)
R
L
Second room
This unit
Third room
Selecting Zone 2 or Zone 3
ZONE 2
ZONE ON/OFF
ZONE 3
ON/OFF
ZONE CONTROL
ZONE2
ZONE3
No indicator flashes when this unit is selected.