Yamaha RX-V2400 User Manual
60
REMOTE CONTROL FEATURES
You can control other components by setting the
appropriate manufacturer codes. Codes can be set up for
each input area.
appropriate manufacturer codes. Codes can be set up for
each input area.
The following table shows the default component
(Library: component category) and the manufacturer code
for each area.
(Library: component category) and the manufacturer code
for each area.
You may not be able to operate your Yamaha component even if
Yamaha manufacture code is initially set as listed above. In this
case, try to set other Yamaha manufacture code(s).
Yamaha manufacture code is initially set as listed above. In this
case, try to set other Yamaha manufacture code(s).
1
Press an input selector button to select the
source component you want to set up.
source component you want to set up.
2
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object.
using a ballpoint pen or similar object.
“SETUP” and the selected component name appear
alternately in the display window.
alternately in the display window.
Be sure to press and hold LEARN for at least 3
seconds, otherwise the learning process will start.
seconds, otherwise the learning process will start.
y
Complete each of the following steps in 30 seconds.
Otherwise, the learning mode will be automatically
canceled. In this case, press LEARN again.
Otherwise, the learning mode will be automatically
canceled. In this case, press LEARN again.
3
Press
k
/
n
to select the name of your
component’s manufacturer.
You will find the names of most worldwide audio-
video manufacturers in alphabetical order in the
display window.
video manufacturers in alphabetical order in the
display window.
If you want to change a library (component
category), press
category), press
l
/
h
. You can set a different
type of component.
Library choices: L:DVD, L:LD, L:CD, L:CDR,
L:MD, L:TAP (tape), L:TUN, L:AMP*, L:TV,
L:CAB (cable), L:DBS, L:SAT, L:VCR
L:MD, L:TAP (tape), L:TUN, L:AMP*, L:TV,
L:CAB (cable), L:DBS, L:SAT, L:VCR
* The amplifier Library (L:AMP) code is preset to “YPC”
to operate this unit. However, you can switch between the
following four codes if necessary.
following four codes if necessary.
YPC
To operate this unit.
ZONE
(U.S.A., Canada and Australia models only)
To operate ZONE 2 or ZONE 3 features.
To operate ZONE 2 or ZONE 3 features.
DSP
To operate Yamaha DSP amplifiers that cannot be
operated with the YPC code.
operated with the YPC code.
NO
To operate other manufactures’ amplifiers using
this unit’s remote control.
this unit’s remote control.
4
Press one of the buttons shaded below to
see if you can control your component. If you
can, the manufacturer code is correct.
see if you can control your component. If you
can, the manufacturer code is correct.
y
• If the manufacturer of your component has more than one
codes, try each of them until you find the correct one.
• If you continuously want to set up another code for
another component, press ENTER and repeat steps 1, 3
and 4.
and 4.
Setting manufacturer codes
Input area
Component
category
(Library)
Manufacturer
PHONO
TV –
V-AUX
VCR –
TUNER
TUNER
Yamaha-1
MD/TAPE
MD
Yamaha-1
CD-R
CD-R
Yamaha
CD
CD
Yamaha-1
DTV
TV
–
CBL/SAT
CABLE
–
VCR 1
VCR
–
DVR/VCR2
VCR
–
DVD
DVD
Yamaha-1
Note
PHONO
CD
DVD
DVR/VCR2
VCR 1
DTV
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
LEARN
ENTER
INPUT MODE
SOUND
TITLE
MENU
CHAPTER
PAUSE
STOP
POWER
REC
SELECT
DISPLAY
SEARCH
SOURCE
PLAY
–
+
ENTER
00_RX-V2400U_EN.book Page 60 Friday, October 10, 2003 10:54 AM