Yamaha RX-V2400 User Manual
TROUBLESHOOTING
81
English
ADDITIONAL
INFO
RMA
T
IO
N
N
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
■
General
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
This unit fails to turn
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters in the
standby mode soon
after the power has
been turned on.
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters in the
standby mode soon
after the power has
been turned on.
The power cord is not connected or the
plug is not completely inserted.
plug is not completely inserted.
Connect the power cord firmly.
—
The impedance setting is incorrect.
Set the impedance to match your speakers.
23
The protection circuitry has been
activated.
activated.
Make sure all speaker wire connections on this unit
and on all speakers are secure and that the wire for
each connection does not touch anything other than
its respective connection.
and on all speakers are secure and that the wire for
each connection does not touch anything other than
its respective connection.
12—14
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
external electric shock (such as lightning
and strong static electricity).
Set this unit in the standby mode, disconnect the
power cord, plug it back in after 30 seconds, then use
it normally.
power cord, plug it back in after 30 seconds, then use
it normally.
—
On screen display
does not appear.
does not appear.
The setting for the on-screen display is set
to “DISPLAY OFF”.
to “DISPLAY OFF”.
Select the full or short display mode.
44
GRAY BACK in the SET MENU is set to
OFF, and no video signal is currently
being received.
OFF, and no video signal is currently
being received.
Set GRAY BACK to AUTO to always show the OSD.
56
No sound
Incorrect input or output cable
connections.
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
the cables may be defective.
16—19
INPUT MODE is set to DTS or
ANALOG.
ANALOG.
Select AUTO.
34
No appropriate input source has been
selected.
selected.
Select an appropriate input source with INPUT,
MULTI CH INPUT or the input selector buttons.
MULTI CH INPUT or the input selector buttons.
30
Speaker connections are not secure.
Secure the connections.
12
The front speakers to be used have not
been selected properly.
been selected properly.
Select the front speakers with SPEAKERS A and/or
B.
B.
30
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or any operation buttons of this unit to
cancel a mute and adjust the volume.
cancel a mute and adjust the volume.
31
If you are playing an LD source, the
player may not output digital signals if the
LD source was not digitally recorded.
player may not output digital signals if the
LD source was not digitally recorded.
Set the INPUT MODE to ANALOG.
34
The INPUT MODE is set to ANALOG
while playing a source encoded with a
DTS signal.
while playing a source encoded with a
DTS signal.
Set the INPUT MODE to AUTO or DTS.
34
The signals this unit cannot reproduce are
being received from a source component
e.g.: a CD-ROM.
being received from a source component
e.g.: a CD-ROM.
Play a source whose signals this unit can reproduce.
—
No picture
The output and input for the picture are
connected to different types of video
jacks.
connected to different types of video
jacks.
Turn on the video conversion function.
56
00_RX-V2400U_EN.book Page 81 Friday, October 10, 2003 10:54 AM