GE 28110 User Manual

10330 North Meridian Street

Indianapolis, IN 46290

© 2006 Thomson Inc. 

Trademark(s) ® Registered

Marca(s) Registrada(s)

Model 28110 

00016114 (Rev. 0 Dom E) 

06-30 

Printed in China

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference; and (2) This device 

must accept any interference received, including interference that may cause undesired 

operation.
This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna for radio or 

television that is “receiving” the interference).

• Reorient or relocate and increase the separation between the telecommunications 

equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit different 

from that to which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an 

experienced radio/television technician for additional suggestions. Also, the Federal 

Communications Commission has prepared a helpful booklet, “How To Identify and 

Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. 

Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-

000-00345-4 when ordering copies.
Notice: The changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to  operate the equipment.

This telephone system meets FCC standards for Hearing Aid Compatibility.

This equipment complies with FCC RF radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated with 

a minimum distance of 20 centimeters between the radiator and your body. This 

transmitter must not be co-located or operated in conjunction with any other antenna 

or transmitter.”
For body worn operation, this phone has been tested and meets the FCC RF exposure 

guidelines when used with the belt clip supplied with this product. Use of other 

accessories may not ensure compliance with FCC RF exposure guidelines.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK

            DO NOT OPEN

WARNING: TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT  TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU  OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

Make sure your package includes the items shown here.

1.  Locate battery and battery door which are packaged together inside a plastic 

bag and are separate from the handset.

2.  Locate the battery compartment on the back of the handset.
3.  Plug the battery pack cord into the jack inside  the compartment.

4.  Insert the battery pack.
5.  Close the battery compartment by pushing the door up until it snaps into place.
6.  Place the handset in the base  to charge.

1.  Plug the AC power converter of the extra charging cradle into the electrical outlet.
2.  Place the handset in the extra charging cradle. The charge indicator turns on, 

verifying the battery is charging. 

3.  Allow the phone to charge for 16 hours prior to first use.

YOU MUST REGISTER THE HANDSET TO THE MAIN BASE BEFORE USE!
After the optional handset has charged for 16 hours on the extra charger, 

NEEDS REGISTRATION shows in the display.

1.  Press the mute/program button. 

PRESS HANDSET PROGRAM shows in the display. (Your handset should be held 

near the base during registration process.)

2.  Press and hold the page button on the base unit until the charge/in use indicator 

flashes.  Press the handset mute/program button.  

REGISTERING shows in the 

display. 

HANDSET X REGISTERED shows in the handset display, where X is the 

handset number. You may now rename your handset. (Refer to Step 3 & 4 of 

Handset Name Section)