Sunfire CRM-2C User Manual
User's Manual
10
Specifi cations
Design
2-way High Pressure
Magnetically Shielded
Magnetically Shielded
Drive Units
HF: Waveguide loaded Neodymium
Ribbon
LF: Dual 4.5-inch High Back-emf
Ribbon
LF: Dual 4.5-inch High Back-emf
Frequency Response
95 Hz to 40 kHz
Crossover Frequency
1.5 kHz
Maximum Power
400 watts
Minimum Power
25 watts
Sensitivity
(2.83 V/1 meter)
90 dB
Maximum Output
115 dB
Impedance
8 ohms nominal
Connections
Gold plated 5-way binding posts
Finish
Ebonized Rosewood
Dimensions
CRM-2
Height 8.25" (210 mm)
Width 5.5" (140 mm)
Depth 6.0" (152 mm)
Weight 9 lbs (4.1 kg)
Width 5.5" (140 mm)
Depth 6.0" (152 mm)
Weight 9 lbs (4.1 kg)
CRM-2C
Height 6.0" (152 mm)
Width 17" (432 mm)
Depth 3.75" (96 mm)
Weight 10.5 lbs (4.8 kg)
Width 17" (432 mm)
Depth 3.75" (96 mm)
Weight 10.5 lbs (4.8 kg)
© 2006 Sunfi re Corporation.
All rights reserved. Sunfi re Corporation
re serves the right to improve its products
at any time. Therefore, specifi cations are
subject to change without notice.
All rights reserved. Sunfi re Corporation
re serves the right to improve its products
at any time. Therefore, specifi cations are
subject to change without notice.
Manual 913-138-00 Rev A
Troubleshooting
The Cinema Ribbon loudspeakers are
designed and built to provide years of
trou ble-free per for mance. Most prob-
lems that occur can usually be solved by
checking your setup, or by making sure
all com po nents are fully op er a tion al.
trou ble-free per for mance. Most prob-
lems that occur can usually be solved by
checking your setup, or by making sure
all com po nents are fully op er a tion al.
The following information will help you
deal with common problems you may ex-
pe ri ence during normal use. If a problem
persists, please contact your Dealer for
assistance.
pe ri ence during normal use. If a problem
persists, please contact your Dealer for
assistance.
Poor or no sound
•
Check all the connections from the
loudspeaker to the amplifi er or receiver.
Swap loudspeakers around, and see
if the poor sound follows a particular
loudspeaker.
loudspeaker to the amplifi er or receiver.
Swap loudspeakers around, and see
if the poor sound follows a particular
loudspeaker.
•
Check that your amplifi er is not driven
too hard or is clipping. Even a low-pow-
ered amp driven into clipping can cause
distortion or damage to your loudspeak-
ers.
too hard or is clipping. Even a low-pow-
ered amp driven into clipping can cause
distortion or damage to your loudspeak-
ers.
•
Many processor/preamps can send
test tones through all the loudspeakers
in your system. Use this to adjust the
volume of each chan nel until they are
all playing at the same level. Make sure
that any bass man age ment options are
set correctly, and any channels using
the Cinema Ribbons are set to "small."
test tones through all the loudspeakers
in your system. Use this to adjust the
volume of each chan nel until they are
all playing at the same level. Make sure
that any bass man age ment options are
set correctly, and any channels using
the Cinema Ribbons are set to "small."
•
If the system bass is weak only when
playing surround sources, check that
your processor is correctly set to decode
the sur round modes, such as Dolby
Digital or DTS.
playing surround sources, check that
your processor is correctly set to decode
the sur round modes, such as Dolby
Digital or DTS.
•
Some DVD discs have a menu that
allows you to select which soundtrack
to play. Check that the correct surround
audio soundtrack is selected.
allows you to select which soundtrack
to play. Check that the correct surround
audio soundtrack is selected.