Tascam LM-8ST User Manual
6
TASCAM LM-8ST
Rear panel
t
ST 2/AUX OUTPUTS (XLR connectors)
Theses balanced XLR connectors output the ST 2/AUX
bus signal.
(1: GND 2: HOT 3: COLD)
bus signal.
(1: GND 2: HOT 3: COLD)
y1
ST 2/AUX OUTPUTS (RCA pin jacks)
These unbalanced RCA pin jacks output the ST 2/AUX
bus signal.
bus signal.
u1
ST 1 OUTPUTS (RCA pin jacks)
These unbalanced RCA pin jacks output the ST1 bus
signal.
signal.
i1
ST 1 OUTPUTS (XLR connectors)
Theses balanced XLR connectors output the ST 1 bus
signal.
(1: GND 2: HOT 3: COLD)
signal.
(1: GND 2: HOT 3: COLD)
o1
Signal ground (SIGNAL GND) connector
Use a commercially available PVC-covered cord to
connect this connector to the signal ground. Note that
this is NOT an electrical safety ground (earth).
connect this connector to the signal ground. Note that
this is NOT an electrical safety ground (earth).
p1
Ground lift (GND LIFT) switch
Even when the ground connector is used to ground the
unit, this ground connection can be interrupted (ground
lift) by setting the
unit, this ground connection can be interrupted (ground
lift) by setting the
GND LIFT
switch to the left.
a1
BUSS OUTPUT connectors
The ST 2/AUX bus signal is output through these
balanced TRS connectors. (Tip: HOT, Ring: COLD,
Sleeve: GND)
balanced TRS connectors. (Tip: HOT, Ring: COLD,
Sleeve: GND)
s1
MASTER BUSS IN switch
Set where the signals input from the
MASTER BUSS IN
connectors are sent.
d1
MASTER BUSS IN input connectors
The signal input through the balanced
TRS MASTER
BUSS IN
connectors can be set to be sent to the ST 1
(MAIN), ST 2/AUX or both busses at once.
f1
LEVEL switches
Set the nominal input/output levels for the channel
inputs/outputs to +4 dBu or –10 dBV.
inputs/outputs to +4 dBu or –10 dBV.
g1
STEREO INPUTS (L/MONO) connectors
These are balanced TRS line input connectors for each
channel. (Tip: HOT, Ring: COLD, Sleeve: GND)
channel. (Tip: HOT, Ring: COLD, Sleeve: GND)
h1
Power connector
Use the included power cord to connect the power
source.
source.
CAUTION
When using this unit, always use the included power
cord. Moreover, do not use the included power cord
with any other equipment. Misuse of a power cord could
cause malfunction, fire or electric shock.
cord. Moreover, do not use the included power cord
with any other equipment. Misuse of a power cord could
cause malfunction, fire or electric shock.
Bottom panel
j
j1
ST 2/AUX switch
Set this to
ST 2
to send the input signals directly to the
ST 2/AUX buss after being adjusted by the
ST 2/AUX
knobs. Since this has no effect on the signals sent to
the ST 1 buss, this unit can be used as mixer with two
independent stereo busses.
Set this to
the ST 1 buss, this unit can be used as mixer with two
independent stereo busses.
Set this to
AUX
to send the signals to the ST 2/AUX
buss after being adjusted by the ST 1 and then the
ST 2/
AUX
knobs. Set this way, ST 1 can be used as the main
buss and ST 2/AUX can be used as an AUX send.
2 − Names and Functions of Parts