temco-tool 39rdvdsn User Manual
23
RDVDSN Series Direct Vent Gas Fireplace
20007894
Log Installation - 33RDVDSN
1. Open glass door (if installed).
2. Remove logs from the packaging. (As with all plastic,
2. Remove logs from the packaging. (As with all plastic,
these bags are not toys and should always be kept
away from children and infants.)
away from children and infants.)
3. Place rear log on back bracket. Ensure that log is
firmly positioned and there is no side-to-side move-
ment.
ment.
4. Place the front log on the front burner (starting to-
ward the rear of the front burner) and slide it forward
until the notches lock into place.
until the notches lock into place.
5. Place the top logs onto the locator notches. Ensure
that the logs are secure. (Fig. 40)
Installation of Logs, Lava Rock & Ember Material
Unpack the logs from packaging and remove each log
from its wrapping materials.
from its wrapping materials.
The logs are fragile and should be handled
with care. Keep the packaging material out
of the reach of children and dispose of the
material in a safe manner.
with care. Keep the packaging material out
of the reach of children and dispose of the
material in a safe manner.
The embers supplied with your fireplace
are made from a high grade rock wool and
should be handled carefully. Wash your
hands immediately after touching to avoid
irritation. The embers must be placed
correctly in order to function properly.
are made from a high grade rock wool and
should be handled carefully. Wash your
hands immediately after touching to avoid
irritation. The embers must be placed
correctly in order to function properly.
Log Installation - 36/39RDVDSN
Attention: Glass door should be removed when install-
ing logset and prior to lighting the unit.
1. Remove glass door (Refer to “Window Frame Re-
ing logset and prior to lighting the unit.
1. Remove glass door (Refer to “Window Frame Re-
moval”).
2. Remove logs from carton and inspect. Refer to Fig-
ure 41.
3. Rear log should be installed onto rear log supports.
Match up slots on rear of log with the vertical log
bracket tabs. Push log back as far as it will go.
bracket tabs. Push log back as far as it will go.
4. The front log should be placed on the front log sup-
ports, slots aligned with tabs and log bottom in chan-
nel.
nel.
5. Top twigs can then be placed in their designated po-
sitions provided with pins on back logs and grooves
on the front log. Front log must be upright.
on the front log. Front log must be upright.
TL119
DV1000/DV1200
logs
12/11/03 djt
TL119
Fig. 41 Correct log placement for 36/39RDVDSN.
Fig. 40 33RDVDSN log placement.
TL126
33RDVN logs
9/04
TL126
All Models
6. Place platinum embers loosely along top surface
6. Place platinum embers loosely along top surface
of burner along entire length of ported area of front
burner. DO NOT place embers on back portion of
burner. Use individual pieces of embers no larger
than dime size, about 1/16” thick (fluffed up thick-
ness). Use a single layer of embers and DO NOT
overlap pieces. Ember material should be fluffed up
and not compressed. When properly placed, all em-
bers will glow red. Adding more embers than neces-
sary will detract from appearance.
burner. DO NOT place embers on back portion of
burner. Use individual pieces of embers no larger
than dime size, about 1/16” thick (fluffed up thick-
ness). Use a single layer of embers and DO NOT
overlap pieces. Ember material should be fluffed up
and not compressed. When properly placed, all em-
bers will glow red. Adding more embers than neces-
sary will detract from appearance.
7. Ember tray ends beyond burner port area and area
in front of grate may be covered with lava rock to
suit individual appearance preferences.
suit individual appearance preferences.