Electrolux ewt113 User Manual
The washing machine can stop during
the spin stage of a wash because of an
out of balance condition. The display will
show “ ” and you will hear a short
beep every minute.
the spin stage of a wash because of an
out of balance condition. The display will
show “ ” and you will hear a short
beep every minute.
Always press buttons gently. Watch the
lights on the control panel to see the
effect pressing a button or turning a
program selector knob has, and listen
for ‘BEEPS’.
lights on the control panel to see the
effect pressing a button or turning a
program selector knob has, and listen
for ‘BEEPS’.
When you press a button you will get a
short ‘BEEP’ to acknowledge the entry.
If the option is not available at the time,
the machine will not allow you to select
it, and you will here the long ‘BEEP’ to
remind you the option is not available.
After the machine has started, the entire
wash option button will be disabled and
machine will show “ ” on the display
with three short beeps to indicate the
button is disabled. The start button is still
active but you need to press and hold
short ‘BEEP’ to acknowledge the entry.
If the option is not available at the time,
the machine will not allow you to select
it, and you will here the long ‘BEEP’ to
remind you the option is not available.
After the machine has started, the entire
wash option button will be disabled and
machine will show “ ” on the display
with three short beeps to indicate the
button is disabled. The start button is still
active but you need to press and hold
the button for 1.2 seconds to pause
machine.
This is to confirm that you really want to
pause the machine. When in pause
mode, all options will be able to be
changed again.
pause the machine. When in pause
mode, all options will be able to be
changed again.
Out of balance during spin is caused by
an uneven distribution of clothes in the
wash bowl. To rectify the out of balance
condition, open the lid and redistribute
the clothes evenly in the space between
the agitator and wall of the wash bowl.
Closing the lid will start the machine
and continue the spin stage of the
wash.
If you have frequent out of balance
interruptions, it may be due to your
washing machine not standing firm and
level on the floor. This can be corrected
by adjusting the washing machine legs
as described in the Installation
Instructions supplied with your machine.
an uneven distribution of clothes in the
wash bowl. To rectify the out of balance
condition, open the lid and redistribute
the clothes evenly in the space between
the agitator and wall of the wash bowl.
Closing the lid will start the machine
and continue the spin stage of the
wash.
If you have frequent out of balance
interruptions, it may be due to your
washing machine not standing firm and
level on the floor. This can be corrected
by adjusting the washing machine legs
as described in the Installation
Instructions supplied with your machine.
Out of Balance Interruption
Power failure recovery
Button Response and Lights
All functions of the washing machine
will stop when the lid is open.
When there is power failure while
machine is washing or rinsing or
spinning. The machine tries to save the
settings at which stage the machine is
doing and then when the power returns
back the machine shows “ ” on the
digital display.
machine is washing or rinsing or
spinning. The machine tries to save the
settings at which stage the machine is
doing and then when the power returns
back the machine shows “ ” on the
digital display.
If the Program dial or any other setting
is not changed within 5 seconds then
the machine starts washing from the
stage where it is left off.
is not changed within 5 seconds then
the machine starts washing from the
stage where it is left off.
This mode permits you to either enable
or disable the beeping (3 beeps every 4
minutes) at the end of the wash. As an
example, you might wish to disable this
beeping when you start a wash when
going to bed, so that when the wash
finished approximately 1 hour later, it will
not disturb you through the night.
or disable the beeping (3 beeps every 4
minutes) at the end of the wash. As an
example, you might wish to disable this
beeping when you start a wash when
going to bed, so that when the wash
finished approximately 1 hour later, it will
not disturb you through the night.
Enabling/Disabling
End-of-Wash Beeping Mode
NOTE: All error beeping is not
disabled by this feature, such as a
critical fault, or lid open during
fill/agitate/spin, or out of balance
during spinning.
To change the “beeping” selection,
proceed as follows:
proceed as follows:
8