SMSC USB2250 User Manual
Ultra Fast USB 2.0 Multi-Slot Flash Media Controller
Datasheet
Revision 1.1 (05-29-08)
18
SMSC USB2250/50i/51/51i
DATASHEET
General Purpose
I/O
I/O
GPIO4
(SCL/xD_ID)
118
I/O12
GPIO: This pin may be used either as input,
edge sensitive interrupt input, or output.
edge sensitive interrupt input, or output.
O12
SCL: This is the clock output when used with
an external EEPROM.
an external EEPROM.
I/O12
xD_ID: This is the xD card detection pin only
applicable to the USB2250/USB2250i.
applicable to the USB2250/USB2250i.
General Purpose
I/O
I/O
GPIO5
(SDA)
5
I/O12
This pin may be used either as input, edge
sensitive interrupt input, or output.
sensitive interrupt input, or output.
SDA: This is the data pin when used with an
external serial EEPROM.
external serial EEPROM.
General Purpose
I/O
I/O
GPIO8 /
CRD_PWR0
14
I/O12
GPIO: This pin may be used either as input,
edge sensitive interrupt input, or output.
edge sensitive interrupt input, or output.
I/O200
CRD_PWR: Card Power drive of 3.3V @
either 100mA or 200mA.
either 100mA or 200mA.
General Purpose
I/O
I/O
GPIO9 /
CRD_PWR1
78
I/O12
GPIO: This pin may be used either as input,
edge sensitive interrupt input, or output.
edge sensitive interrupt input, or output.
I/O200
CRD_PWR: Card Power drive of 3.3V @
either 100mA or 200mA.
either 100mA or 200mA.
General Purpose
I/O
I/O
GPIO10 /
CRD_PWR2
76
I/O12
GPIO: These pins may be used either as
input, edge sensitive interrupt input, or
output. It is a requirement that this is the
only FET used to power SM devices. Failure
to do this will violate SM voltage specification
on SM device pins.
input, edge sensitive interrupt input, or
output. It is a requirement that this is the
only FET used to power SM devices. Failure
to do this will violate SM voltage specification
on SM device pins.
I/O200
CRD_PWR: Card Power drive of 3.3V @
either 100mA or 200mA.
either 100mA or 200mA.
General Purpose
I/O
I/O
GPIO11 /
CRD_PWR3
16
I/O12
GPIO: These pins may be used either as
input, edge sensitive interrupt input, or
output.
input, edge sensitive interrupt input, or
output.
I/O200
CRD_PWR: Card Power drive of 3.3V @
either 100mA or 200mA.
either 100mA or 200mA.
RESET Input
nRESET
64
IS
This active low signal is used by the system
to reset the chip. The active low pulse should
be at least 1
to reset the chip. The active low pulse should
be at least 1
μs wide.
TEST Input
TEST
103
I
This signal is used for testing the chip. User
should normally tie this pin low externally, if
the test function is not used.
should normally tie this pin low externally, if
the test function is not used.
Regulator
Enable
Enable
REG_EN
6
IPU
This signal is used to enable the internal
1.8V regulator.
1.8V regulator.
Table 5.1 USB2250/50i/51/51i 128-Pin VTQFP Pin Descriptions (continued)
NAME
SYMBOL
128-PIN
VTQFP
BUFFER
TYPE
DESCRIPTION