Thermador CD365 User Manual
CABINET CONSIDERATIONS AND COUNTERTOP CUTOUT
1. INSTALLING THE COOKTOP IN NORMAL
COUNTERTOPS (For solid surface cooktop,
see Section 2, below)
see Section 2, below)
A.
Instructions are based on Standard American
cabinets 36" high x 24" deep with a 25"
countertop.
cabinets 36" high x 24" deep with a 25"
countertop.
B.
Provide approximately a 10 square inch opening
in the toe kick area or other cabinet area for
adequate air inlet to the cabinet.
in the toe kick area or other cabinet area for
adequate air inlet to the cabinet.
C.
Seal the Cooktop
Apply the foam tape packaged with the cooktop
to underside of the cooktop along the perimeter
before installing. See Fig. 4 on Page 23.
Apply the foam tape packaged with the cooktop
to underside of the cooktop along the perimeter
before installing. See Fig. 4 on Page 23.
D.
Attach Brackets to the Cooktop
Attach clamps of the hold-down brackets
packaged with the cooktop to the rough-in box.
Use the washer and screws provided. See Fig. 4
on Page 23.
Attach clamps of the hold-down brackets
packaged with the cooktop to the rough-in box.
Use the washer and screws provided. See Fig. 4
on Page 23.
E.
Install the Cooktop
Insert cooktop into the cutout. Adjust hold-
down brackets to desired position and tighten
screws to rough-in box. Insert adjusting screw
into clamp and secure cooktop to countertop.
See Fig. 4 on Page 23.
Insert cooktop into the cutout. Adjust hold-
down brackets to desired position and tighten
screws to rough-in box. Insert adjusting screw
into clamp and secure cooktop to countertop.
See Fig. 4 on Page 23.
2. INSTALLING THE COOKTOP IN SOLID
SURFACE COUNTERTOPS
Always consult the countertop manufacturer for
specific instructions
Always consult the countertop manufacturer for
specific instructions
Cooktop
30" Models 36" Models
45" Models
A
20 to
20" to
20" to
Cut-out
20-3/8"
20-3/8"
20-3/8"
B
29" to
35" to
44" to
Cut-out
29-3/8"
35-3/8"
44-3/8"
C
30"
36"
45"
Overall
1-3/4" Min. to Combus-
tible Rear Wall
A
21" Cooktop
3-1/2" Min. to
Side Wall
4" Below Countertop
1-3/4" Min. to
Counter Front
Counter Front
1/8" Min.
Clearance
From Cooktop
to Start of Radius
Clearance
From Cooktop
to Start of Radius
6-1/2" Min. to
Left Side Wall
Note: Cooktop may be installed undercounter as close as
construction allows. Good practice is to leave some
airspace at bottom and sides.
construction allows. Good practice is to leave some
airspace at bottom and sides.
Note: For overhead cabinets and
side wall clearances see Fig. 1.
side wall clearances see Fig. 1.
➝
➝
➝
➝
Figure 2 - Cutout Dimensions Are Underlined
B
C
Page 22
Countertops made from natural (i.e. granite and marble)
or SOLID SURFACE MATERIALS, such as Surell™ and
Corian®, require special cutout preparation and
installation procedures. Follow the guidelines in
preparing the cutout dimensions. Install the cooktop as
follows:
or SOLID SURFACE MATERIALS, such as Surell™ and
Corian®, require special cutout preparation and
installation procedures. Follow the guidelines in
preparing the cutout dimensions. Install the cooktop as
follows:
A.
Round Corners on Cutout
Round the cutout corners according to
instructions from the countertop manufacturer.
Round the cutout corners according to
instructions from the countertop manufacturer.
B.
Seal the Cooktop
Apply heat reflective tape (such as Scotch
Apply heat reflective tape (such as Scotch
®
Aluminum Foil Tape #425 or #427) around the
cutout so that it folds over the top and side
surfaces. Be sure the tape extends beyond the
outermost flange of the cooktop. All corners
should also be covered with tape. Let bottom
edge of tape hang free. See Fig. 3 on Page 23.
cutout so that it folds over the top and side
surfaces. Be sure the tape extends beyond the
outermost flange of the cooktop. All corners
should also be covered with tape. Let bottom
edge of tape hang free. See Fig. 3 on Page 23.
C.
Attach Brackets
Attach brackets to the burner box using washers
and screws provided. Use a wooden block
underneath the countertop before tightening
the bracket screws. See Fig. 4 on Page 23
Attach brackets to the burner box using washers
and screws provided. Use a wooden block
underneath the countertop before tightening
the bracket screws. See Fig. 4 on Page 23
2-1/4" Min.
to Back
Wall
to Back
Wall