Philips AZ1017 User Manual

– AC power cord 

1)

1 Source selector: CD,TUNER,

TAPE/OFF 
– selects CD, tuner (MW or FM) or tape

source of sound 

– switch off the set 

2 VOLUME – adjusts volume level 

3 LIFT•OPEN – opens the CD door

4 MIC (built-in microphone) – for voice 

recording via cassette recording 

5 Cassette recorder keys:

; – pauses playback or recording
9/ – stops the tape;

– opens the cassette holder

5 or 6 – fast winds/ rewinds tape
1 – starts playback 
0 – starts recording 

6 CD Display – shows the CD functions 

7 PROG – programs and reviews 

programmed track numbers 

8 REPEAT – repeats a track/

CD program/entire CD 

9 BAND – selects FM or MW waveband 

0 TUNING – tunes to radio stations 

!

2; – starts or pauses CD playback.
9 – stop playback;

– erases a CD program 

∞, § – skips or searches a passage/track

backwards 

1) 

@ Telescopic antenna – improves FM 

reception 

# Battery compartment – open to insert 6

x 1.5V R-14/ UM2/ C-cells

$ p – 3.5 mm stereo headphone socket

% AC MAINS – inlet for power cord 
^ Voltage selector – adjust to match the

local voltage 110/220V before plugging in the
set 

Whenever convenient, use the mains supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.

Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity
as indicated by the "+" and "–" symbols inside
the compartment. (See 1)

Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.

•  Incorrect use of batteries can cause 

electrolyte leakage and will corrode the 
compartment or cause the batteries to burst:

•  Do not mix battery types: e.g. alkaline with

carbon zinc. Only use batteries of the same
type for the set.

•  When inserting new batteries, do not try to

mix old batteries with the new ones.

•  Remove the batteries if the set is not to be

used for a long time.

Check if the power/mains voltage, as shown

, corresponds to your

local power supply. If it does not, consult your
dealer or service center.

If your set is equipped with a voltage 
selector, adjust the selector so that it 
matches with the local power supply.

Connect the power cord to the AC MAINS
inlet and the wall socket.The mains lead is
now connected and ready for use.

To switch the set off completely, withdraw the
power cord from the wall socket.

Install the unit near the AC outlet and where
the AC power plug can be easily reached.

•

Disconnect the mains lead from the wall
socket to protect your set during heavy 
thunderstorms. Children could seriously injure
themselves as the free end of the cable may
still be live if only the connector is removed
from the MAINS socket at the back of the
unit.

–

To avoid unnecessary energy consumption,
always adjust the source selector to

after using the set, and also

check that the tape deck keys are released.

To select your sound source, adjust the

to : CD, TUNER or

.

To switch off the set, adjust the source

to TAPE/OFF position and check

the cassette keys are released.

–

To change from TAPE to TUNER or CD
function, or when you are switching off the set:
first, make sure you press the tape 

9/ key to

Adjusting volume 
Adjust the volume with the VOLUME
control.

Adjust the source selector to TUNER.

Adjust BAND to FM or MW as your
desired band.

Turn TUNING to tune to a station.

•

For FM, extend and turn the telescopic
antenna for best reception. Reduce its length
if the signal is too strong.

•

For MW, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.

To switch off the radio, adjust the source
selector to TAPE/OFF position and check
the cassette keys are released.