Philips dvd580m-p01 User Manual
12
English
Inserting batteries into the
Remote Control
Remote Control
1
Open the battery cover.
2
Insert batteries (AA size) with the correct
polarity as indicated by the
polarity as indicated by the
+ and - symbols
inside the battery compartment.
3
Close the cover.
CAUTION!
– Remove batteries if they are exhausted
or not to be used for a long time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances,
so they should be disposed off properly
and kept away from children.
– Remove batteries if they are exhausted
or not to be used for a long time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances,
so they should be disposed off properly
and kept away from children.
Using the Remote Control
● Direct the remote control at the remote sensor
of the DVD player.
● Do not drop the remote control.
● Do not leave the remote control near extremely
● Do not leave the remote control near extremely
hot or humid place.
● Do not spill water or put anything wet on the
remote control.
NTSC/PAL Conversion
● This player is equipped with an NTSC/PAL
conversion feature that converts the video
output of the disc to match your TV system.
output of the disc to match your TV system.
● Allows you to select between PAL, NTSC and
MULTI mode.
The conversions supported are as follows:
The conversions supported are as follows:
NTSC
PAL
NTSC
Not
Supported
PAL
PAL
NTSC
PAL
NTSC
NTSC
PAL
PAL
Disc
Output format
Type
DVD
VCD
NTSC
Format
Selected mode
PAL
NTSC
PAL
NTSC
PAL
AUTO
1
Press VIDEO SYS on the remote control to
access the preference video standard.
access the preference video standard.
Notes:
– If you have a PAL only TV, ensure that your
PAL/NTSC setting is PAL.
– MULTI can only be selected when using a TV
that has both the NTSC and PAL systems.
– This setting is applicable for CVBS output on
cinch and SCART only.
– Slight picture distortions may occur due to this
conversion. This is normal. Thus, the MULTI format
is most suitable for the best picture quality.
– If you have a PAL only TV, ensure that your
PAL/NTSC setting is PAL.
– MULTI can only be selected when using a TV
that has both the NTSC and PAL systems.
– This setting is applicable for CVBS output on
cinch and SCART only.
– Slight picture distortions may occur due to this
conversion. This is normal. Thus, the MULTI format
is most suitable for the best picture quality.
Switching On
1
Connect the AC power cord to the power
outlet.
outlet.
2
Switch on the TV and DVD player.
3
Set the TV to the correct Video IN channel. (eg.
EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc.
(Refer to your TV owner’s manual for detail)
➜ The player display lights up and the default
screen appears on the TV.
EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc.
(Refer to your TV owner’s manual for detail)
➜ The player display lights up and the default
screen appears on the TV.
4
If you are using an external equipment (eg. audio
system or receiver), turn them on and select the
appropriate input source that was used to
connect to the DVD player output. Refer to the
equipment owner’s manual for detail.
system or receiver), turn them on and select the
appropriate input source that was used to
connect to the DVD player output. Refer to the
equipment owner’s manual for detail.
COAXIAL
OPTICAL
VIDEO
S-VIDEO
Y
Pr/Cr
Pb/Cb
12V
FL
SL
Center
FR
SR
Sub-W
Multi-5.1
AC
MAINS
AC power cord
12V ADAPTOR
Preparation