Philips horizon mcs 100 satellite User Manual
20
There is a wide range of audio and video equipment that can be connected to your TV.
The following connection diagrams show you how to connect them.
The following connection diagrams show you how to connect them.
Note:
EXT. 1
can handle CVBS and RGB,
EXT. 2
CVBS, RGB and Y/C,
EXT. 3
and
EXT. 4
only CVBS.
It is preferred to connect peripherals with RGB output to
EXT. 1
or
2
as RGB provides a better picture quality.
If your recorder is provided with the EasyLink function, it should be connected to
EXT. 2
to benefit from the
EasyLink functionality.
Recorder
(VCR-DVD+RW)
Connect the aerial cables 1, 2 and, to obtain the optimum
picture quality, eurocable 3 as shown.
If your recorder does not have a euroconnector, the only possible
connection is via the aerial cable.You will therefore need to tune in
your recorder’s test signal and assign it programme number 0 or
store the test signal under a programme number between 90 and
99, see Manual installation, p. 7.
See the handbook of your recorder.
picture quality, eurocable 3 as shown.
If your recorder does not have a euroconnector, the only possible
connection is via the aerial cable.You will therefore need to tune in
your recorder’s test signal and assign it programme number 0 or
store the test signal under a programme number between 90 and
99, see Manual installation, p. 7.
See the handbook of your recorder.
Decoder and Recorder
Connect a eurocable 4 to your decoder and to the special
euroconnector of your recorder. See also the recorder handbook.
See Decoder, p. 10. You can also connect your decoder directly to
euroconnector of your recorder. See also the recorder handbook.
See Decoder, p. 10. You can also connect your decoder directly to
EXT. 1
or
2
with a eurocable.
Other equipment
(satellite receiver, decoder, DVD, games, etc.)
&
Connect the aerial cables 1, 2 and 3 as shown (only if your
peripheral has TV aerial in-/output).
Connect your equipment with a eurocable 4 or 5 to one of the
euroconnectors
peripheral has TV aerial in-/output).
Connect your equipment with a eurocable 4 or 5 to one of the
euroconnectors
EXT.1
,
2
,
3
or
4
to obtain a better picture quality.
é
Look for the test signal of your peripheral in the same way as you
do for a recorder.
do for a recorder.
“
Make a selection in the Setup, Source menu, p. 10.
Side connections
Camera or Camcorder
&
Connect your camera or camcorder as shown.
é
Connect to
VIDEO
2 and
AUDIO L
3 for mono equipment.
For stereo equipment also connect
AUDIO R
3.
S-VHS quality with an S-VHS camcorder is obtained by connecting
the S-VHS cables with the S-video input 1 and audio inputs 3.
Do not connect cable 1 and 2 at the same time. This may cause
picture distortion !
the S-VHS cables with the S-video input 1 and audio inputs 3.
Do not connect cable 1 and 2 at the same time. This may cause
picture distortion !
Headphone
&
Insert the plug into the headphone socket L as shown.
é
Press ¬ on the remote control to switch off the internal
loudspeakers of the TV.
The headphone impedance must be between 8 and 4000 Ohm. The
headphone socket has a 3.5 mm jack.
In the Sound menu select Headphone volume to adjust the
headphone volume.
loudspeakers of the TV.
The headphone impedance must be between 8 and 4000 Ohm. The
headphone socket has a 3.5 mm jack.
In the Sound menu select Headphone volume to adjust the
headphone volume.
AUDIO
VIDEO
S•VIDEO
1
2
3
2
EXT.
EXT.
2
EXT.
CABLE
1
4
2
3
1/2
1/2
EXT.
EXT.
1/2
EXT.
CABLE
1
2
3
5
4
Connect Peripheral Equipment
2229.1 gb 12-03-2003 09:55 Pagina 20