Philips th-37pr10u User Manual
36
Options
On
Weekly Command Timer
Onscreen display
Off
Initial INPUT
1/3
Maximum VOL level
Initial VOL level
Button lock
INPUT lock
Advanced PIP
Remocon User level
Off
Off
0
0
Off
Off
Off
Off
Options Adjustments
Item
Effect Adjustments
Initial VOL
level
Off
On
Press
button to adjust the volume when the unit is turned on.
Off
On
Off:
Sets normal volume.
On:
Sets your preferred volume.
Notes:
• When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options menu if you
• When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options menu if you
adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL
level
Off
On
Press
button to adjust the maximum volume.
Off
On
Off:
Sets auto maximum volume.
On:
Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• You can hear the changed volume regardless of your volume setting before opening the options menu if you
• You can hear the changed volume regardless of your volume setting before opening the options menu if you
adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lock
Off
PC
INPUT1
INPUT2
INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input
in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input
signal. (Ex. INPUT1A, INPUT1B)
Button lock
Off
MENU&ENTER
On
Off:
All the buttons at the bottom of the main unit can be used.
MENU & ENTER: Locks
MENU
and
ENTER/
buttons on bottom face of main unit.
On:
Locks all the button on bottom face of main unit.
Sets Button lock with the unit buttons in the following procedure.
Off:
Press four times
→Press
INPUT
four times
→Press four times→Press
ENTER/
MENU & ENTER:
Press
ENTER/
four times
→Press four times→Press
INPUT
four times
→Press
ENTER/
On:
Press four times
→Press
ENTER/
four times
→Press four times→Press
ENTER/
Remocon
User level
Off
User1
User2
User3
Off:
You can use all of the buttons on the remote control.
User1: You can only use
,
,
,
, ,
,
,
buttons on the remote control.
User2: You can only use
,
, buttons on the remote control.
User3: Locks all the buttons on remote control.
Advanced PIP
Off
On
Off:
Sets normal two screen display mode (see page 20).
On:
Sets Advanced PIP mode (see page 21).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
•
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
•
,
buttons are unavailable during Advanced PIP mode operation.