Hanna Instruments hi 983319-0 User Manual

Manufacturers since 1978

These Instruments are in

Compliance with the CE Directives

Hanna Instruments reserves the right to modify the design, construction and

appearance of its products without advance notice.

These meters are warranted for two years against defects in work-

manship and materials when used for their intended purpose and
maintained according to instructions. The probe is warranted for a
period of six months. This warranty is limited to repair or replacement

free of charge.
Damages due to accident, misuse, tampering or lack of prescribed main-

tenance are not covered.
If service is required, contact the dealer from whom you purchased the

instrument. If under warranty, report the model number, date of pur-
chase, serial number and the nature of the failure. If the repair is not
covered by the warranty, you will be notified of the charges incurred. If

the instrument is to be returned to Hanna Instruments, first obtain a
Returned Goods Authorization Number from the Customer Service depart-
ment and then send it with shipment costs prepaid. When shipping any

instrument, make sure it is properly packaged for complete protection.
To validate your warranty, fill out and return the enclosed warranty card

within 14 days from the date of purchase.
All rights are reserved. Reproduction in whole or in part is prohibited

Dear Customer,
Thank you for choosing a Hanna product. This manual will

provide you with the necessary information for the correct

operation of the meter. Please read it carefully before using

the meter. If you need additional technical information, do

not hesitate to e-mail us at tech@hannainst.com.
These instruments are in compliance with the   directives.

HI 983319-0 and HI 983319-1  are conductivity  indicators

and controllers with a relay output designed for simplicity of

use in a wide range of  applications.
The models are panel mounted with membrane keypads on

the front panel and an easy-to-read LCD display.
All the meters automatically compensate for temperature

variations. The probe is easy to clean and requires little

maintenance.
Measurements are highly accurate and the meters can be

calibrated at one point.
Power supply, wiring and selection are made via the plug-

in terminal blocks on the rear panel.
LED indicators on the front panel identify whether the

controller is in set or measurement mode, and if alarm is

active.

Recommendations for Users
Before using these products, make sure that they are entirely suitable for

the environment in which they are used. Operation of these instruments in

residential areas could cause unacceptable interferences to radio and TV

equipment. The metal band at the end of the probe is sensitive to electro-
static discharges. Avoid touching this metal band at all times. During op-

eration, ESD wrist straps should be worn to avoid possible damage to the

probe by electrostatic discharges. Any variation introduced by the user to

the supplied equipment may degrade the instrument’s EMC performance.
To avoid electrical shock, do not use these instruments when voltage at the
measurement surface exceeds 24 VAC or 60 VDC. Use plastic beakers to

minimize any EMC interferences.
To avoid damage or burns, do not perform any measurement in microwave

ovens.

ISTR983319R5  12/2001

h t t p : / / w w w . h a n n a i n s t . c o m

Range

0 to 1999 ppm

Resolution

 1 ppm

Accuracy (@ 20°C)

±2% f.s.

Setpoint

Adjustable through multiturn trimmer

Alarm Condition LED ON and alarm contact closed when

TDS value is lower than Setpoint

Alarm Output

2-contact relay, no fuse protected.

5A, 240 VAC, 30 VDC

Probe

HI 7634-00 EC/TDS probe

Temp. Compensation Automatic from 5 to 50°C

(41 to 122°F) with ß=2%

TDS Conversion Factor

  0.65

Calibration

Manual, at one point through trimmer

Cal. Solution

HI7031 (1413 µS/cm)

Power supply:

 External

HI983319-0

12  VDC

HI983319-1

 115/230 VAC; 50/60Hz

Dimensions

 79 x 49 x 95 mm (3.1 x 1.9 x 3.7”)

Weight:
HI983319-0

140 g (4.96 oz)

HI983319-1

 250 g (8.85 oz)

Remove the instrument from the packing material and

examine it carefully. If any damage has occurred during

shipment, immediately notify your Dealer or the nearest

Hanna Customer Service Center.
The meter is supplied with:

• Instruction manual;

• Mounting brackets.
Note: Conserve all packing material until the instrument

has been observed to function correctly. Any defective

item must be returned in its original packing.